參數資料
型號： TMS28F004AFT90BDCDL
廠商： Texas Instruments, Inc.
英文描述： 524288 BY 8-BIT/262144 BY 16-BIT AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
中文描述： 524288按8-BIT/262144由16位自動選擇啟動塊閃存
文件頁數： 11/80頁
文件大?。?/td> 1080K
代理商： TMS28F004AFT90BDCDL
TMS28F004Axy, TMS28F400Axy
524288 BY 8-BIT/
262
144 BY 16-BIT
AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
SMJS829A – JANUARY 1996 – REVISED AUGUST 1997
11
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
status register (continued)
Table 5. Status-Register Bit Definitions and Functions
STATUS
BIT
FUNCTION
DATA
COMMENTS
SB7
Write state machine status
Write-state-machine status
1= Ready
0= Busy
If SB7 = 0 (busy), the WSM has not completed an erase or
programming operation. If SB7 = 1 (ready), other polling
operations can be performed. Until this occurs, the other status
bits are not valid If the WSM status bit shows busy (0) the user
bits are not valid. If the WSM status bit shows busy (0), the user
must toggle E or G periodically to determine when the WSM has
completed an operation (SB7 = 1) since SB7 is not updated
automatically at the completion of a WSM task.
SB6
Erase-suspend status (ESS)
1= Erase suspended
0= Erase in progress or
completed
When an erase-suspend command is issued, the WSM halts
execution and sets the ESS bit high (SB6 = 1) indicating that the
erase operation has been suspended. The WSM status bit also
is set high (SB7 = 1) indicating that the erase-suspend operation
has been completed successfully. The ESS bit remains at a
logic-high level until an erase-resume command is input to the
CSM (code D0h).
SB5
Erase status (ES)
1= Block erase error
0= Block erase good
SB5 = 0 indicates that a successful block erasure has occurred.
SB5 = 1 indicates that an erase error has occurred. In this case,
the WSM has completed the maximum allowed erase pulses
determined by the internal algorithm, but this was insufficient to
erase the device completely.
SB4
Program status (PS)
1= Byte/word program error
0= Byte/word program good
SB4 = 0 indicates successful programming has occurred at the
addressed block location. SB4 = 1 indicates that the WSM was
unable to program the addressed block location correctly.
SB3
VPP status (VPPS)
1= Program abort:
VPP range error
0= VPP good
SB3 provides information on the status of VPP during
programming. If VPP is lower than VPPL after a program or erase
command has been issued, SB3 is set to a 1 indicating that the
programming operation is aborted. If VPP is between VPPH and
VPPL, SB3 is not set.
SB2–
SB0
Reserved
These bits must be masked out when reading the status register.
byte-wide or word-wide mode selection
The memory array is divided into two parts: an upper-half that outputs data through I/O pins DQ8–DQ15, and
a lower-half that outputs data through DQ0–DQ7. Device operation in either byte-wide or word-wide mode is
user-selectable and is determined by the logic state of BYTE. When BYTE is at a logic-high level, the device
is in the word-wide mode and data is written to, or read from, I/O pins DQ0–DQ15. When BYTE is at a logic-low
level, the device is in the byte-wide mode and data is written to or read from I/O pins DQ0–DQ7. In the byte-wide
mode, I/O pins DQ8–DQ14 are placed in the high-impedance state and DQ15/A
–1
becomes the low-order
address pin and selects either the upper or lower half of the array. Array data from the upper half (DQ8–DQ15)
and the lower half (DQ0–DQ7) are multiplexed to appear on DQ0–DQ7. Table 6, Table 7, and Table 8
summarize operational modes.
相關PDF資料
PDF描述
TMS28F004AFT90CDBJL 524288 BY 8-BIT/262144 BY 16-BIT AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
TMS28F004AFT90CDCDL 524288 BY 8-BIT/262144 BY 16-BIT AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
TMS28F004AMB60BDBJL 524288 BY 8-BIT/262144 BY 16-BIT AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
TMS28F004AMB60CDBJL 524288 BY 8-BIT/262144 BY 16-BIT AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
TMS28F004AMB70BDBJL 524288 BY 8-BIT/262144 BY 16-BIT AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
相關代理商/技術參數
參數描述
TMS28F004AFT90CDBJL 制造商:TI 制造商全稱:Texas Instruments 功能描述:524288 BY 8-BIT/262144 BY 16-BIT AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
TMS28F004AFT90CDCDL 制造商:TI 制造商全稱:Texas Instruments 功能描述:524288 BY 8-BIT/262144 BY 16-BIT AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
TMS28F004AMB60BDBJL 制造商:TI 制造商全稱:Texas Instruments 功能描述:524288 BY 8-BIT/262144 BY 16-BIT AUTO-SELECT BOOT-BLOCK FLASH MEMORIES
TMS28F004AMB60BDCDE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
TMS28F004AMB60BDCDL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*