![](http://datasheet.mmic.net.cn/130000/TMDS461PZT_datasheet_5021429/TMDS461PZT_8.png)
ABSOLUTE MAXIMUM RATINGS
SLLS915 – JANUARY 2009 ............................................................................................................................................................................................... www.ti.com
Table 2. Control Pin Lookup Table(1)
SIGNAL
LEVEL
STATE
DESCRIPTION
H
Normal Mode
Normal operational mode for device.
LP
Low-power
Device is forced into a low power state, causing the inputs and outputs to go to a
L
mode
high-impedance state. All other inputs are ignored.
S2
S1
L
Port 1
Port 1 is selected as the active port; all other ports are disabled.
S[2:1]
L
H
Port 2
Port 2 is selected as the active port; all other ports are disabled.
GPIO Mode
H
L
Port 3
Port 3 is selected as the active port; all other ports are disabled.
H
Port 4
Port 4 is selected as the active port; all other ports are disabled.
H
I2C
Device is configured by I2C logic.
I2C_SEL
L
GPIO
Device is configured by GPIO.
H
0101101
The 7-bit address for the local I2C logic is 0101101
Local_Addr
L
0101100
The 7-bit address for the local I2C logic is 0101100
H
Offset 1
DDC sink side VOL and VIL offset range 1, VIL1 (max) : 0.4V, VOL1 (max) : 0.7V
OVS
L
Offset 2
DDC sink side VOL and VIL offset range 2, VIL2 (max) : 0.4V, VOL2 (max) : 0.6V
Hi-Z
Offset 3
DDC sink side VOL and VIL offset range 3, VIL3 (max) : 0.3V, VOL3 (max) : 0.5V
Driver output voltage swing precision control to aid with system compliance. VSadj resistor
Compliant
VSadj
4.02 k
value could be selected to be
Voltage Swing
4.02 k
±10% based on the system requirement to pass HDMI compliance.
(1)
(H) Logic high; (L) Logic low
ORDERING INFORMATION(1)
PART NUMBER
PART MARKING
PACKAGE
TMDS461PZTR
TMDS461
100-pin TQFP reel
TMDS461PZT
TMDS461
100-pin TQFP tray
(1)
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
over operating free-air temperature range (unless otherwise noted)
(1)
VALUE
UNIT
Supply voltage range(2)
VCC
–0.3 to 3.6
V
Voltage range
TMDS I/O
–0.3 to 4
HPD and DDC I/O
–0.3 to 5.5
V
Control and status I/O
–0.3 to 5.5
Electrostatic discharge
Human body model(3) on SCL[1:4], SDA[1:4], D[0:2]+_[1:4], D[0:2]–_[1:4],
±10,000
CLK+_[1:4], CLK–_[1:4] pins
Human body model(3) on all other pins
±6,000
V
Charged-device model(4)
±1500
Machine model(5)
±200
Continuous power dissipation
See Dissipation Ratings
table
(1)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2)
All voltage values, except differential voltages, are with respect to network ground terminal.
(3)
Tested in accordance with JEDEC Standard 22, Test Method A114-B
(4)
Tested in accordance with JEDEC Standard 22, Test Method C101-A
(5)
Tested in accordance with JEDEC Standard 22, Test Method A115-A
8
Copyright 2009, Texas Instruments Incorporated