參數資料
型號: TMDS461PZIT
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PQFP100
封裝: PLASTIC, TQFP-100
文件頁數: 13/24頁
文件大?。?/td> 1467K
代理商: TMDS461PZIT
PRODUCTPREVIEW
Slave Address
EXAMPLE – WRITING TO THE TMDS461
SLLS915 – AUGUST 2008 ................................................................................................................................................................................................. www.ti.com
address. Following this initial acknowledge by the slave, the master device becomes the receiver. When the
master has received the requested data byte from the slave, the not acknowledge (A) condition is initiated by the
master by keeping the SDA signal high just before it asserts the stop (P) condition. This sequence terminates a
read cycle as shown in Figure 18. Note that the TMDS461 does not allow multiple read transfers to occur. See
Example – Reading from the TMDS461 section for more information.
Figure 19. I2C Write Cycle
Figure 20. I2C Read Cycle
Both SDA and SCL must be connected to a positive supply voltage via a pull-up resistor. These resistors should
comply with the I2C specification that ranges from 2 k
to 19 k. When the bus is free, both lines are high. The
address byte is the first byte received following the START condition from the master device. The 7-bit address is
factory preset to 010110x. Table 9 lists the calls that the TMDS461 will respond to.
Table 9. TMDS461 Slave Address
FIXED ADDRESS
READ/WRITE BIT
Bit 7 (MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0 (R/W)
0
1
0
1
0
x
1/0
The proper way to write to the TMDS461 is illustrated as follows:
An I2C master initiates a write operation to the TMDS461 by generating a start condition (S) followed by the
TMDS461 I2C address (as shown below), in MSB-first bit order, followed by a 0 to indicate a write cycle. After
receiving an Acknowledge from the TMDS461, the master presents the sub-address (sink port) to write
consisting of one byte of data, MSB first. The TMDS461 acknowledges the byte after completion of the transfer.
Finally the master presents the data to write to the register (sink port) and the TMDS461 acknowledges the byte.
The I2C master then terminates the write operation by generating a stop condition (P). Note that the TMDS461
does not support multi-byte transfers. To write to both sink ports, or registers, this procedure must be repeated
for each register one series at a time (i.e., repeat steps 1 through 8 for each sink port).
Step 1
0
I2C Start (Master)
S
Step 2
7
6
5
4
3
2
1
0
I2C General Address (Master)
0
1
0
1
0
X
0
20
Copyright 2008, Texas Instruments Incorporated
Product Folder Link(s) :TMDS461
相關PDF資料
PDF描述
TMDS461PZT SPECIALTY CONSUMER CIRCUIT, PQFP100
TMDS461PZTR SPECIALTY CONSUMER CIRCUIT, PQFP100
TMP431BDGKT SPECIALTY ANALOG CIRCUIT, PDSO8
TMP435ADGST SPECIALTY ANALOG CIRCUIT, PDSO10
TMS320AV100PBM SPECIALTY CONSUMER CIRCUIT, PQFP120
相關代理商/技術參數
參數描述
TMDS461PZT 功能描述:視頻開關 IC 4 to 1 HDMI Switch RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻(最大值):12 Ohms 傳播延遲時間: 開啟時間(最大值): 關閉時間(最大值): 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel
TMDS461PZTR 功能描述:視頻開關 IC 4 to 1 HDMI Switch RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻(最大值):12 Ohms 傳播延遲時間: 開啟時間(最大值): 關閉時間(最大值): 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel
TMDS570LS12HDK 功能描述:TMS570LS Hercules? MCU 32-Bit ARM? Cortex?-R4F Embedded Evaluation Board 制造商:texas instruments 系列:Hercules? 零件狀態:有效 板類型:評估平臺 類型:MCU 32-位 核心處理器:ARM? Cortex?-R4F 操作系統:- 平臺:- 配套使用產品/相關產品:TMS570LS 安裝類型:固定 內容:板,電纜,配件 標準包裝:1
TMDS570LS31HDK 制造商:Texas Instruments 功能描述:HERCULES DEVELOPMENT KIT
TMDS570LS31USB 功能描述:EVAL BOARD HERCULES 制造商:texas instruments 系列:Hercules? 零件狀態:停產 板類型:評估平臺 類型:MCU 32-位 核心處理器:ARM? Cortex?-R4F 操作系統:- 平臺:- 配套使用產品/相關產品:TMS570LS 安裝類型:固定 內容:板,電纜,配件 標準包裝:1