參數資料
型號: TMC3503KRC50
廠商: FAIRCHILD SEMICONDUCTOR CORP
元件分類: DAC
英文描述: Triple Video D/A Converter 8 bit, 80 Msps, 5V
中文描述: PARALLEL, 8 BITS INPUT LOADING, 0.015 us SETTLING TIME, 8-BIT DAC, PQFP48
封裝: PLASTIC, LQFP-48
文件頁數: 2/14頁
文件大?。?/td> 69K
代理商: TMC3503KRC50
TMC3503
PRODUCT SPECIFICATION
2
REV. 1.02 11/24/99
Functional Description
The TMC3503 is a low-cost triple 8-bit CMOS D/A con-
verter designed to directly drive computer CRT displays at
pixel rates up to 80 Msps. It comprises three identical 8-bit
D/A converters with registered data inputs, common clock,
and internal voltage reference. An independent current
source allows sync to be added to any D/A converter output.
Digital Inputs
All digital inputs are TTL-compatible. Data are registered on
the rising edge of the CLK signal. The analog output
changes t
DO
after the rising edge of CLK. There is one stage
of pipeline delay on the chip. The guaranteed clock rates of
the TMC3503 are 80, 50, and 30 MHz.
SYNC and BLANK
SYNC and BLANK inputs control the output level
(Figure 1 and Table 1) of the D/A converters during CRT
retrace intervals. BLANK forces the D/A outputs to the
blanking level while SYNC turns off a separate current
source which is brought off the chip through the IO
S
pin.
Figure 1. Nominal Output Levels
IO
S
may be connected to any one D/A output, or used inde-
pendently. It is commonly tied to the green D/A converter for
“Sync on Green” operation. This connection adds a 40 IRE
sync pulse to the D/A output and brings that D/A output to
0.0 Volts during the sync tip. SYNC and BLANK are regis-
tered on the rising edge of CLK.
BLANK gates the D/A inputs and sets the pedestal voltage.
If BLANK = HIGH, the D/A inputs are added to a pedestal
which offsets the current output. If BLANK = LOW, data
inputs and the pedestal are disabled.
WHITE
The WHITE control drives all three D/As to full-scale, over-
riding the data inputs. It is overridden by the BLANK input,
and is independent of SYNC.
data: 660 mV max.
65-3503-02
pedestal: 54 mV
sync: 286 mV
SLEEP
The SLEEP control, when HIGH, places the TMC3503 in a
power-down state. This function operates asynchronously.
D/A Outputs
Each D/A output is a current source. To obtain a voltage out-
put, a resistor must be connected to ground. Output voltage
depends upon this external resistor, the reference voltage,
and the value of the gain-setting resistor connected between
R
REF
and GND.
Normally, a source termination resistor of 75 Ohms is con-
nected between the D/A current output pin and GND near
the D/A converter. A 75 Ohm coaxial cable may then be con-
nected with another 75 Ohm termination resistor at the far
end of the cable. This "double termination" presents the D/A
converter with a net resistive load of 37.5 Ohms.
The TMC3503 may also be operated with a single 75 Ohm
terminating resistor. To lower the output voltage swing to the
desired range, the value of the resistor on R
REF
should be
increased.
Voltage Reference
The TMC3503 has an internal bandgap voltage reference of
+1.235 Volts. An external voltage reference may be con-
nected to the V
REF
pin, overriding the internal voltage refer-
ence. All three D/A converters are driven from the same
reference.
A 0.1μF capacitor must be connected between the COMP
pin and V
DD
to stabilize internal bias circuitry and ensure
low-noise operation.
Power and Ground
The TMC3503 D/A converter requires a single +5.0 Volt
power supply. The analog (V
DD
) power supply voltage
should be decoupled to GND to reduce power supply
induced noise. 0.1μF decoupling capacitors should be placed
as close as possible to the power pins.
The high slew-rate of digital data makes capacitive coupling
to the outputs of any D/A converter a potential problem.
Since the digital signals contain high-frequency components
of the CLK signal, as well as the video output signal, the
resulting data feedthrough often looks like harmonic distor-
tion or reduced signal-to-noise performance. All ground pins
should be connected to a common solid ground plane for
best performance.
相關PDF資料
PDF描述
TMC3503KRC80 Triple Video D/A Converter 8 bit, 80 Msps, 5V
TMC3503 XLR Style Audio Connector; Leaded Process Compatible:Yes
TMC3503R2C30 Triple Video D/A Converter 8 bit, 80 Msps, 5V
TMC3503R2C50 Triple Video D/A Converter 8 bit, 80 Msps, 5V
TMC3533R2C80 Triple Video D/A Converter 8 bit, 80 Msps, 3.3V
相關代理商/技術參數
參數描述
TMC3503KRC80 功能描述:數字化視頻/模擬轉換器集成電路 50Mhz Video D/a Conv Triple 8Bit RoHS:否 制造商:Texas Instruments 轉換器數量:3 輸出類型:Current 轉換速率:180 MSPs 分辨率:10 bit 接口類型:Parallel 電壓參考:Internal or External 積分非線性:- 2.5 LSB, 1.5 LSB 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:HTQFP 封裝:Tray
TMC3503R2C30 功能描述:數字化視頻/模擬轉換器集成電路 50Mhz Video D/a Conv Triple 8Bit RoHS:否 制造商:Texas Instruments 轉換器數量:3 輸出類型:Current 轉換速率:180 MSPs 分辨率:10 bit 接口類型:Parallel 電壓參考:Internal or External 積分非線性:- 2.5 LSB, 1.5 LSB 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:HTQFP 封裝:Tray
TMC3503R2C30_Q 功能描述:數模轉換器- DAC 50Mhz Video D/a Conv Triple 8Bit RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
TMC3503R2C50 功能描述:數字化視頻/模擬轉換器集成電路 50Mhz Video D/a Conv Triple 8Bit RoHS:否 制造商:Texas Instruments 轉換器數量:3 輸出類型:Current 轉換速率:180 MSPs 分辨率:10 bit 接口類型:Parallel 電壓參考:Internal or External 積分非線性:- 2.5 LSB, 1.5 LSB 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:HTQFP 封裝:Tray
TMC3503R2C80 功能描述:數字化視頻/模擬轉換器集成電路 50Mhz Video D/a Conv Triple 8Bit RoHS:否 制造商:Texas Instruments 轉換器數量:3 輸出類型:Current 轉換速率:180 MSPs 分辨率:10 bit 接口類型:Parallel 電壓參考:Internal or External 積分非線性:- 2.5 LSB, 1.5 LSB 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:HTQFP 封裝:Tray