- 您現在的位置：買賣IC網 > PDF目錄384010 > TLV2775AQDRQ1 (Texas Instruments, Inc.) FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS WITH SHUTDOWN PDF資料下載
參數資料
| 型號： | TLV2775AQDRQ1 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS WITH SHUTDOWN |
| 中文描述： | 2.7家庭- V高，擺率軌到軌輸出運算放大器具有關斷 |
| 文件頁數： | 32/41頁 |
| 文件大?。?/td> | 839K |
| 代理商： | TLV2775AQDRQ1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
SGLS179B SEPTEMBER 2003 REVISED APRIL 2006
32
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
gain calculation
Since the TLV2772 is capable of rail-to-rail output using a 3-V supply, V
O
= 0 (min) to 3 V (max). With no signal
from the sensor, nominal V
O
= reference voltage = 1.23 V. Therefore, the maximum negative swing from nominal
is 0 V 1.23 V = 1.23 V and the maximum positive swing is 3 V 1.23 V = 1.77 V. By modeling the shock sensor
as a low impedance voltage source with output of 2.25 mV/g (max) in the x and y axis and 1.7 mV/g (max) in
the z axis, the gain of the circuit is calculated by equation 1.
Gain
Output Swing
Sensor Signal
Acceleration
(1)
To avoid saturation of the operational amplifier, the gain calculations are based on the maximum negative swing
of 1.23 V and the maximum sensor output of 2.25 mV/g (x and y axis) and 1.70 mV/g (z axis).
Gain (x, y)
1.23 V
2.25 mV g
50 g
10.9
(2)
Gain (z)
–1.23 V
1.70 mV g
–50 g
14.5
(3)
and
By selecting R3 = 10 k
and R4 = 100 k
, in the x and y channels, a gain of 11 is realized. By selecting
R3 = 7.5 k
and R4 = 100 k
, in the z channel, a gain of 14.3 is realized. The schematic shows the configuration
for either the x- or y-axis.
bandwidth calculation
To calculate the component values for the frequency shaping characteristics of the signal conditioning circuit,
1 Hz and 500 Hz are selected as the minimum required 3-dB bandwidth.
To minimize the value of the input capacitor (C1) required to set the lower cutoff frequency requires a large value
resistor for R2 is required. A 1-M
resistor is used in this example. To set the lower cutoff frequency, the required
capacitor value for C1 is:
C1
1
2 f
LOW
R
2
0.159
μ
F
(4)
Using a value of 0.22
μ
F, a more common value of capacitor, the lower cutoff frequency is 0.724 Hz.
To minimize the phase shift in the feedback loop caused by the input capacitance of the TLV2772, it is best to
minimize the value of the feedback resistor R4. However, to reduce the required capacitance in the feedback
loop a large value for R4 is required. Therefore, a compromise for the value of R4 must be made. In this circuit,
a value of 100 k
has been selected. To set the upper cutoff frequency, the required capacitor value for C2 is:
C2
1
2 f
HIGH
R
4
3.18
μ
F
(5)
Using a 2.2-nF capacitor, the upper cutoff frequency is 724 Hz.
R5 and C3 also cause the signal response to roll off. Therefore, it is beneficial to design this roll-off point to begin
at the upper cutoff frequency. Assuming a value of 1 k
for R5, the value for C3 is calculated to be
0.22
μ
F.
相關PDF資料 |
PDF描述 |
|---|---|
| TLV2775AQPWRQ1 | FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS WITH SHUTDOWN |
| TLV2775QDRQ1 | FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS WITH SHUTDOWN |
| TLV2775QPWRQ1 | FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS WITH SHUTDOWN |
| TLV277XA-Q1 | FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS WITH SHUTDOWN |
| TLV277X-Q1 | FAMILY OF 2.7-V HIGH-SLEW-RATE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS WITH SHUTDOWN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLV2775CD | 功能描述:運算放大器 - 運放 Quad 2.7V Rail-Rail RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| TLV2775CDG4 | 功能描述:運算放大器 - 運放 Quad 2.7V Rail-Rail RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| TLV2775CDR | 功能描述:IC OPAMP GP R-R 5.1MHZ 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品變化通告:Discontinuation 18/May/2012 標準包裝:2,000 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.42 V/µs 增益帶寬積:1.5MHz -3db帶寬:- 電流 - 輸入偏壓:15nA 電壓 - 輸入偏移:1000µV 電流 - 電源:116µA 電流 - 輸出 / 通道:100mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5 V，±0.9 V ~ 2.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:851 (CN2011-ZH PDF) 其它名稱:296-20930-2 |
| TLV2775CN | 功能描述:運算放大器 - 運放 Quad 2.7V Rrail-Rail RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| TLV2775CNE4 | 功能描述:運算放大器 - 運放 Quad 2.7V Hi-Slew-Rt R-to-R Out w/Shtdwn RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。