參數資料
型號: TLV1571CPW
廠商: Texas Instruments, Inc.
英文描述: 2.7 V TO 5.5 V, 1-/8-CHANNEL, 10-BIT, PARALLEL ANALOG-TO-DIGITAL CONVERTERS
中文描述: 2.7 V至5.5 V,1-/8-CHANNEL,10位,并行模擬數字轉換器
文件頁數: 16/29頁
文件大?。?/td> 434K
代理商: TLV1571CPW
TLV1571, TLV1578
2.7 V TO 5.5 V, 1-/8-CHANNEL, 10-BIT,
PARALLEL ANALOG-TO-DIGITAL CONVERTERS
SLAS170C –MARCH 1999 – REVISED FEBRUARY 2000
16
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
grounding and decoupling considerations
General practices should apply to the PCB design to limit high frequency transients and noise that are fed back
into the supply and reference lines. This requires that the supply and reference pins be sufficiently bypassed.
In most cases 0.1-
μ
F ceramic chip capacitors are adequate to keep the impedance low over a wide frequency
range. Since their effectiveness depends largely on the proximity to the individual supply pin, they should be
placed as close to the supply pins as possible.
To reduce high frequency and noise coupling, it is highly recommended that digital and analog grounds be
shorted immediately outside the package. This can be accomplished by running a low impedance line between
DGND and AGND under the package.
TLV1571/78
100 nF
DGND
DVDD
AVDD
AGND
REFP
REFM
100 nF
100 nF
VREFP
VREFM
AVDD
DVDD
Figure 9. Placement for Decoupling Capacitors
power supply ground layout
Printed-circuit boards that use separate analog and digital ground planes offer the best system performance.
Wire-wrap boards do not perform well and should not be used. The two ground planes should be connected
together at the low-impedance power-supply source. The best ground connection may be achieved by
connecting the ADC AGND terminal to the system analog ground plane making sure that analog ground
currents are well managed.
Rs
Ri(MUX)
VS
VC
15 pF
Driving Source
TLV1571/78
Ci
VI
VI= Input Voltage at AIN
VS= External Driving Source Voltage
Rs= Source Resistance
Ri(ADC)= Input Resistance of ADC
Ri(MUX)= Input Resistance (MUX on resistance)
Ci= Input Capacitance
VC= Capacitance Charging Voltage
Driving source requirements:
Noise and distortion for the source must be equivalent to the resolution of the converter.
Rs must be real at the input frequency.
Ri(ADC)
MO
AIN
Figure 10. Equivalent Input Circuit Including the Driving Source
相關PDF資料
PDF描述
TLV2252MFK CARD READER FULL INSERT DBL TRK
TLV2252AMFK Advanced LinCMOSE RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS
TLV2252AMJG Advanced LinCMOSE RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS
TLV2252AMU TRANS ARRAY PNP/PNP MINI-6
TLV2252MJG Advanced LinCMOSE RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS
相關代理商/技術參數
參數描述
TLV1571IDW 功能描述:模數轉換器 - ADC 10bit 1.2 MSPS PA RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLV1571IDWG4 功能描述:模數轉換器 - ADC 10bit 1.2 MSPS PA RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLV1571IPW 功能描述:模數轉換器 - ADC 10bit 1.2 MSPS PA RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLV1571IPWG4 功能描述:模數轉換器 - ADC 1-Ch 10-Bit 1.25MSPS 8-Ch DSP/SPI RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
TLV1572 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.7 V TO 5.5 V, 10-BIT, 1.25 MSPS SERIAL ANALOG-TO-DIGITAL CONVERTER WITH AUTO-POWERDOWN