參數資料
型號: TL1454ACNS
廠商: Texas Instruments, Inc.
英文描述: DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT
中文描述: 雙通道脈寬調制(PWM)控制電路
文件頁數: 4/27頁
文件大?。?/td> 409K
代理商: TL1454ACNS
TL1454A, TL1454AY
DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM)
CONTROL CIRCUIT
SLVS423 A
MAY 2002
REVISED SEPTEMBER 2002
4
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
theory of operation
reference voltage
A linear regulator operating from V
CC
generates a 2.5-V supply for the internal circuits and the 1.26-V reference,
which can source a maximum of 1 mA for external loads. A small ceramic capacitor (0.047
μ
F to 0.1
μ
F) between
REF and ground is recommended to minimize noise pickup.
error amplifier
The error amplifier generates the error signal used by the PWM to adjust the power-switch duty cycle for the
desired converter output voltage. The signal is generated by comparing a sample of the output voltage to the
voltage reference and amplifying the difference. An external resistive divider connected between the converter
output and ground, as shown in Figure 1, is generally required to obtain the output voltage sample.
The amplifier output is brought out on COMP to allow the frequency response of the amplifier to be shaped with
an external RC network to stabilize the feedback loop of the converter. DC loading on the COMP output is limited
to 45
μ
A (the maximum amplifier source current capability).
Figure 1 illustrates the sense-divider network and error-amplifier connections for converters with positive output
voltages. The divider network is connected to the noninverting amplifier input because the PWM has a phase
inversion; the duty cycle decreases as the error-amplifier output increases.
_
+
IN
IN+
R3
R1
R2
COMP
To PWM
VO
Compensation
Network
REF
Converter
Output
TL1454A
Figure 1. Sense Divider/Error Amplifier
Configuration for Converters with Positive Outputs
The output voltage is given by:
VO
Vref
1
R1
R2
where V
ref
= 1.26 V.
The dc source resistance of the error-amplifier inputs should be 10 k
or less and approximately matched to
minimize output voltage errors caused by the input-bias current. A simple procedure for determining appropriate
values for the resistors is to choose a convenient value for R3 (10 k
or less) and calculate R1 and R2 using:
R1
R3VO
VO
Vref
R2
R3VO
Vref
相關PDF資料
PDF描述
TL1454AY DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT
TL1593CNS 780- 】 488-pixel ccd image sensor
TL2575_08 1-A SIMPLE STEP-DOWN SWITCHING VOLTAGE REGULATORS
TL2575ADJI 1-A SIMPLE STEP-DOWN SWITCHING VOLTAGE REGULATORS
TL2575HV 1-A SIMPLE STEP-DOWN SWITCHING VOLTAGE REGULATORS
相關代理商/技術參數
參數描述
TL1454ACNSR 功能描述:DC/DC 開關控制器 Dual ch PWM Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TL1454ACNSRG4 功能描述:DC/DC 開關控制器 Dual ch PWM Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TL1454ACPW 功能描述:DC/DC 開關控制器 Dual-Ch PWM Control Circuit RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TL1454ACPWG4 功能描述:DC/DC 開關控制器 Dual-Ch PWM Control Circuit RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TL1454ACPWR 功能描述:DC/DC 開關控制器 Dual ch PWM Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK