參數資料
型號: TK71615ASCL
廠商: TOKO INC
元件分類: 基準電壓源/電流源
英文描述: LOW DROPOUT VOLTAGE REGULATOR
中文描述: 1.5 V FIXED POSITIVE LDO REGULATOR, 0.35 V DROPOUT, PDSO5
封裝: MINIATURE, SOT-23, 5 PIN
文件頁數: 14/20頁
文件大小: 111K
代理商: TK71615ASCL
Page 14
December 1999 TOKO, Inc.
TK716xx
DEFINITION AND EXPLANATION OF TECHNICAL TERMS (CONT.)
PACKAGE POWER DISSIPATION (P
D
)
This is the power dissipation level at which the thermal
sensor is activated. The IC contains an internal thermal
sensor which monitors the junction temperature. When the
junction temperature exceeds the monitor threshold of
150
°
C, the IC is shut down. The junction temperature
rises as the difference between the input power (V
IN
x I
IN
)
and the output power (V
OUT
x I
OUT
) increases. The rate of
temperature rise is greatly affected by the mounting pad
configuration on the PCB, the board material, and the
ambient temperature. When the IC mounting has good
thermal conductivity, the junction temperature will be low
even if the power dissipation is great. When mounted on
the recommended mounting pad, the power dissipation of
the SOT23-5 is increased to 500 mW. For operation at
ambient temperatures over 25
°
C, the power dissipation of
the SOT23-5 device should be derated at 4.0 mW/
°
C. To
determine the power dissipation for shutdown when
mounted, attach the device on the actual PCB and
deliberately increase the output current (or raise the input
voltage) until the thermal protection circuit is activated.
Calculate the power dissipation of the device by subtracting
the output power from the input power. These
measurements should allow for the ambient temperature
of the PCB. The value obtained from P
D
/(150
°
C - T
A
) is the
derating factor. The PCB mounting pad should provide
maximum thermal conductivity in order to maintain low
device temperatures. As a general rule, the lower the
temperature, the better the reliability of the device. The
thermal resistance when mounted is expressed as follows:
T
j
= 0
jA
x P
D
+ T
A
For Toko ICs, the internal limit for junction temperature is
150
°
C. If the ambient temperature (T
A
) is 25
°
C, then:
150
°
C = 0
jA
x P
D
+ 25
°
C
0
jA
= 125
°
C / P
D
P
D
is the value when the thermal protection circuit is
activated. A simple way to determine P
D
is to calculate V
IN
x I
IN
when the output side is shorted. Input current gradually
falls as temperature rises. You should use the value when
thermal equilibrium is reached.
The range of usable currents can also be found from the
graph below.
Procedure:
1)
2)
3)
4)
Find P
D
P
D1
is taken to be P
D
x (~0.8 - 0.9)
Plot P
D1
against 25
°
C
Connect P
D1
to the point corresponding to the 150
°
C
with a straight line.
In design, take a vertical line from the maximum
operating temperature (e.g., 75
°
C) to the derating
curve.
Read off the value of P
D
against the point at which the
vertical line intersects the derating curve. This is taken
as the maximum power dissipation, D
PD
.
5)
6)
The maximum operating current is:
I
OUT
= (D
PD
/ (V
IN(MAX)
-
V
OUT
)
SOT23-5 POWER DISSIPATION CURVE
PD
DPD
25
50
75
150
(mW)
TA (
°
C)
3
6
5
4
0 50 100 150
TA (
°
C)
P
0
100
500
MOUNTED AS
SHOWN
FREE AIR
200
300
400
相關PDF資料
PDF描述
TK71643ASCL LOW DROPOUT VOLTAGE REGULATOR
TK71644ASCL LOW DROPOUT VOLTAGE REGULATOR
TK71645ASCL LOW DROPOUT VOLTAGE REGULATOR
TK71646ASCL LOW DROPOUT VOLTAGE REGULATOR
TK71623ASCL LOW DROPOUT VOLTAGE REGULATOR
相關代理商/技術參數
參數描述
TK71615ASCLH 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT VOLTAGE REGULATOR
TK71615ASIL 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT VOLTAGE REGULATOR
TK71615ASILH 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT VOLTAGE REGULATOR
TK71615SCL 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT VOLTAGE REGULATOR
TK71615SCLH 制造商:TOKO 制造商全稱:TOKO, Inc 功能描述:LOW DROPOUT VOLTAGE REGULATOR