參數資料
型號: THS5661DW
廠商: Texas Instruments, Inc.
英文描述: 12-BIT, 100 MSPS, CommsDACE DIGITAL-TO-ANALOG CONVERTER
中文描述: 12位,100 MSPS的,CommsDACE數字模擬轉換器
文件頁數: 18/29頁
文件大小: 755K
代理商: THS5661DW
THS5661
12-BIT, 100 MSPS, CommsDAC
DIGITAL-TO-ANALOG CONVERTER
SLAS200A – MAY 1999 – REVISED JULY 1999
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
analog current outputs
Figure 26 shows a simplified schematic of the current source array output with corresponding switches.
Differential PMOS switches direct the current of each individual PMOS current source to either the positive
output node IOUT1 or its complementary negative output node IOUT2. The output impedance is determined
by the stack of the current sources and differential switches, and is typically >300 k
in parallel with an output
capacitance of 5 pF.
Output nodes IOUT1 and IOUT2 have a negative compliance voltage of –1 V, determined by the CMOS process.
Beyond this value, transistor breakdown may occur, resulting in reduced reliability of the THS5661 device. The
positive output compliance depends on the full-scale output current IOUT
FS
and positive supply voltage AV
DD
.
The positive output compliance equals 1.25 V for AV
DD
= 5 V and IOUT
FS
= 20 mA. Exceeding the positive
compliance voltage adversely affects distortion performance and integral nonlinearity. The optimum distortion
performance for a single-ended or differential output is achieved when the maximum full-scale signal at IOUT1
and IOUT2 does not exceed 0.5 V (e.g. when applying a 50
doubly terminated load for 20 mA full-scale output
current). Applications requiring the THS5661 output (i.e., OUT1 and/or OUT2) to extend its output compliance
should size R
LOAD
accordingly.
AVDD
Current Source Array
IOUT1
IOUT2
RLOAD
RLOAD
Current
Sources
Switches
Figure 26. Equivalent Analog Current Output
Figure 27(a) shows the typical differential output configuration with two external matched resistor loads. The
nominal resistor load of 50
will give a differential output swing of 2 V
PP
when applying a 20 mA full-scale output
current. The output impedance of the THS5661 depends slightly on the output voltage at nodes IOUT1 and
IOUT2. Consequently, for optimum dc integral nonlinearity, the configuration of Figure 27(b) should be chosen.
In this I–V configuration, terminal IOUT1 is kept at virtual ground by the inverting operational amplifier. The
complementary output should be connected to ground to provide a dc current path for the current sources
switched to IOUT2. Note that the INL/DNL specifications for the THS5661 are measured with IOUT1 maintained
at virtual ground. The amplifier’s maximum output swing and the DAC’s full-scale output current determine the
value of the feedback resistor R
FB
. Capacitor C
FB
filters the steep edges of the THS5661 current output, thereby
reducing the operational amplifier slew-rate requirements. In this configuration, the op amp should operate on
a dual supply voltage due to its positive and negative output swing. Node IOUT1 should be selected if a
single-ended unipolar output is desirable.
相關PDF資料
PDF描述
THS5661PW 12-BIT, 100 MSPS, CommsDACE DIGITAL-TO-ANALOG CONVERTER
TI-30XIIB Scientific Calculators
TI-30XIIS Scientific Calculators
TIBPAL16L8-30MFK LOW-POWER HIGH-PERFORMANCE IMPACT E PAL CIRCUITS
TIBPAL16R4-30MFK LOW-POWER HIGH-PERFORMANCE IMPACT E PAL CIRCUITS
相關代理商/技術參數
參數描述
THS5661EVM 功能描述:數據轉換 IC 開發工具 THS5661 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
THS5661IDW 制造商:Rochester Electronics LLC 功能描述:- Bulk
THS5661IPW 制造商:Rochester Electronics LLC 功能描述:- Bulk
THS5661PW 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-BIT, 100 MSPS, CommsDACE DIGITAL-TO-ANALOG CONVERTER
THS5671A 制造商:TI 制造商全稱:Texas Instruments 功能描述:14-BIT, 125 MSPS, CommsDAC DIGITAL-TO-ANALOG CONVERTER