- 您現在的位置：買賣IC網 > PDF目錄359289 > THS4302RGTT (Texas Instruments, Inc.) WIDEBAND FIXED-GAIN AMPLIFIER PDF資料下載
參數資料
| 型號： | THS4302RGTT |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 運算放大器 |
| 英文描述： | WIDEBAND FIXED-GAIN AMPLIFIER |
| 中文描述： | 寬頻帶固定增益放大器 |
| 文件頁數： | 15/23頁 |
| 文件大?。?/td> | 602K |
| 代理商： | THS4302RGTT |
www.ti.com
-3
-2.5
-2
-1.5
-1
-0.5
0
0.5
10 M
100 M
1 G
1
f - Frequency - Hz
N
R
(ISO)
= 12.1
,
C
L
= 47 pF
V
S
=
5 V
R
(ISO)
= 8
,
C
L
= 100 pF
R
(ISO)
= 24.9
,
C
L
= 10 pF
ADS807
12-Bit,
53 Msps
IN
R
ISO
0.1
μ
F
16.5
68 pf
0.1
μ
F
IN
CM
1.82 k
_
+
THS4302
R
f
49.9
V
I
+
22
μ
F
47 pF
0.1
μ
F
V
S+
50-
Source
R
g
30.1
FB
FB = Ferrite Bead
* = Low Impedance
*2.5 V
*2.5 V
Power
Recommendations
Supply
Decoupling
Techniques
and
Driving Capacitive Loads
THS4302
SLOS403G–OCTOBER 2002–REVISED JANUARY 2005
devices can easily cause this value to be exceeded.
Always consider this effect carefully, and add the
recommended series resistor as close as possible to
the
THS4302
output
pin
Guidelines).
(see
Board
Layout
The criterion for setting this R
resistor is a
maximum bandwidth, flat frequency response at the
load.
Figure 48. Driving Capacitive Loads
#IMPLIED.
ADCs should be driven differentially. See
the THS4500 family of devices for more
information.
Figure 47. Driving an ADC With a Single-Ended
Input
For best performance, high-speed
Power supply decoupling is a critical aspect of any
high-performance amplifier design process. Careful
decoupling provides higher quality ac performance
(most notably improved distortion performance). The
following guidelines ensure the highest level of per-
formance.
1. Place decoupling capacitors as close to the
power supply inputs as possible, with the goal of
minimizing the inductance of the path from
ground to the power supply. Inductance in series
with the bypass capacitors will degrade perform-
ance. Note that a narrow lead or trace has about
0.8 nH of inductance for every millimeter of
length. Each printed-circuit board (PCB) via also
has between 0.3 and 0.8 nH depending on length
and diameter. For these reasons, it is rec-
ommended to use a power supply trace about the
width of the package for each power supply lead
to the capacitors, and 3 or more vias to connect
the capacitors to the ground plane.
2. Placement priority should put the smallest valued
capacitors closest to the device.
3. Solid power planes can lead to PCB resonances
when they are not properly terminated to the
ground plane over the area and along the per-
imeter of the power plane by high frequency
capacitors. Doing so ensures that there are no
power plane resonances in the needed frequency
range. Values used are in the range of 2 pF - 50
pF,
depending
on
suppressed, with numerous vias for each. Using
One of the most demanding, and yet very common,
load conditions for an op amp is capacitive loading.
Often, the capacitive load is the input of an A/D
converter, including additional external capacitance,
which may be recommended to improve A/D linearity.
High-speed amplifiers like the THS4302 can be
susceptible to decreased stability and closed-loop
response peaking when a capacitive load is placed
directly on the output pin. When the amplifier's
open-loop
output
resistance
capacitive load introduces an additional pole in the
signal path that can decrease the phase margin.
When the primary considerations are frequency re-
sponse flatness, pulse response fidelity, or distortion,
the simplest and most effective solution is to isolate
the capacitive load from the feedback loop by
inserting a series isolation resistor between the
amplifier output and the capacitive load.
is
considered,
this
The Typical Characteristics show the recommended
isolation resistor vs capacitive load and the resulting
frequency response at the load. Parasitic capacitive
loads greater than 2 pF can begin to degrade the
performance of the THS4302. Long PC board traces,
unmatched
cables,
and
connections
to
multiple
the
frequencies
to
be
15
相關PDF資料 |
PDF描述 |
|---|---|
| THV1021 | 2ch Buck/Boost Inverting |
| THV1031 | 3ch Buck, Boost and Inverting Controller |
| TID01BB8 | FIBER OPTIC ISOLATOR, 1570-1610nm, LC/SPC CONNECTOR |
| TJA1054A | Fault-tolerant CAN transceiver |
| TJA1054AU | Fault-tolerant CAN transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS4302RGTTG4 | 功能描述:高速運算放大器 Wideband Fixed Gain Amplifier RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4303 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:WIDEBAND FIXED-GAIN AMPLIFIER |
| THS4303EVM | 功能描述:放大器 IC 開發工具 THS4303 Wideband Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| THS4303RGTR | 功能描述:視頻放大器 Wideband Fixed Gain Amplifier RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS4303RGTRG4 | 功能描述:視頻放大器 Wideband Fixed Gain Amplifier RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。