- 您現在的位置：買賣IC網 > PDF目錄383995 > THS4011JG (Texas Instruments, Inc.) 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS PDF資料下載
參數資料
| 型號： | THS4011JG |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| 中文描述： | 290 - MHz的低失真高速放大器 |
| 文件頁數： | 23/30頁 |
| 文件大?。?/td> | 439K |
| 代理商： | THS4011JG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
THS4011, THS4012
290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS
SLOS216B – JUNE 1999 – FEBRUARY 2000
23
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
general PowerPAD design considerations (continued)
The next consideration is the package constraints. The two sources of heat within an amplifier are quiescent
power and output power. The designer should never forget about the quiescent heat generated within the
device, especially muti-amplifier devices. Because these devices have linear output stages (Class A-B), most
of the heat dissipation is at low output voltages with high output currents. Figure 36 to Figure 39 show this effect,
along with the quiescent heat, with an ambient air temperature of 50
°
C. When using V
CC
=
±
5 V, there is
generally not a heat problem, even with SOIC packages. But, when using V
CC
=
±
15 V, the SOIC package is
severely limited in the amount of heat it can dissipate. The other key factor when looking at these graphs is how
the devices are mounted on the PCB. The PowerPAD devices are extremely useful for heat dissipation. But,
the device should always be soldered to a copper plane to fully use the heat dissipation properties of the
PowerPAD. The SOIC package, on the other hand, is highly dependent on how it is mounted on the PCB. As
more trace and copper area is placed around the device,
θ
JA
decreases and the heat dissipation capability
increases. The currents and voltages shown in these graphs are for the total package. For the dual amplifier
package (THS4012), the sum of the RMS output currents and voltages should be used to choose the proper
package.
Figure 36
Package With
θ
JA < = 120
°
C/W
SO-8 Package
θ
JA = 167
°
C/W
Low-K Test PCB
VCC =
±
5 V
Tj = 150
°
C
TA = 50
°
C
100
80
40
0
0
1
| VO | – RMS Output Voltage – V
2
3
–
I
|
140
180
200
4
5
160
120
60
20
|
Maximum Output
Current Limit Line
THS4011
MAXIMUM RMS OUTPUT CURRENT
vs
RMS OUTPUT VOLTAGE DUE TO THERMAL LIMITS
Safe Operating
Area
Figure 37
100
10
0
3
| VO | – RMS Output Voltage – V
6
9
1000
12
15
Maximum Output
Current Limit Line
SO-8 Package
θ
JA = 167
°
C/W
Low-K Test PCB
SO-8 Package
JA = 98
°
C/W
High-K Test PCB
TJ = 150
°
C
TA = 50
°
C
–
IO
|
|
VCC =
±
15 V
DGN Package
θ
JA = 58.4
°
C/W
THS4011
MAXIMUM RMS OUTPUT CURRENT
vs
RMS OUTPUT VOLTAGE DUE TO THERMAL LIMITS
Safe Operating
Area
相關PDF資料 |
PDF描述 |
|---|---|
| THS4011DGN | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4011EVM | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4011FK | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4011MFK | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4012D | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS4011MFK | 制造商:TI 制造商全稱:Texas Instruments 功能描述:290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4011MFKB | 制造商:Texas Instruments 功能描述:290-MHZ LOW-DISTORTION VOLTAGE-FEEDBACK |
| THS4011MJG | 制造商:Texas Instruments 功能描述:OP AMP SGL VOLT FDBK 16.5V/33V 8CDIP - Rail/Tube |
| THS4011MJGB | 制造商:Texas Instruments 功能描述:OP Amp Single Volt Fdbk ±16.5V/33V 8-Pin CDIP Tube 制造商:Texas Instruments 功能描述:OP AMP SGL VOLT FDBK 16.5V/33V 8CDIP - Rail/Tube |
| THS4012 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
發布緊急采購，3分鐘左右您將得到回復。