- 您現在的位置：買賣IC網 > PDF目錄383995 > THS4011EVM (Texas Instruments, Inc.) 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS PDF資料下載
參數資料
| 型號： | THS4011EVM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| 中文描述： | 290 - MHz的低失真高速放大器 |
| 文件頁數： | 15/30頁 |
| 文件大?。?/td> | 439K |
| 代理商： | THS4011EVM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
THS4011, THS4012
290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS
SLOS216B – JUNE 1999 – FEBRUARY 2000
15
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
noise calculations and noise figure (continued)
_
+
RF
RS
RG
eRg
eRf
eRs
en
IN+
Noiseless
IN–
eni
eno
Figure 25. Noise Model
The total equivalent input noise density (e
ni
) is calculated by using the following equation:
eni
en
2
IN
RS
2
IN–
RF
RG
2
4 kTRs
4 kT RF
RG
Where:
k = Boltzmann’s constant = 1.380658
×
10
–23
T = Temperature in degrees Kelvin (273 +
°
C)
R
F
|| R
G
= Parallel resistance of R
F
and R
G
To get the equivalent output noise of the amplifier, just multiply the equivalent input noise density (e
ni
) by the
overall amplifier gain (A
V
).
eno
eniAV
e
ni
1
R
F
R
G
(noninverting case)
As the previous equations show, to keep noise at a minimum, small value resistors should be used. As the
closed-loop gain is increased (by reducing R
G
), the input noise is reduced considerably because of the parallel
resistance term. This leads to the general conclusion that the most dominant noise sources are the source
resistor (R
S
) and the internal amplifier noise voltage (e
n
). Because noise is summed in a root-mean-squares
method, noise sources smaller than 25% of the largest noise source can be effectively ignored. This can greatly
simplify the formula and make noise calculations much easier to calculate.
For more information on noise analysis, please refer to the Noise Analysissection in Operational Amplifier
Circuits Applications Report(literature number SLVA043).
相關PDF資料 |
PDF描述 |
|---|---|
| THS4011FK | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4011MFK | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4012D | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4012DGN | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4012EVM | 290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS4011FK | 制造商:TI 制造商全稱:Texas Instruments 功能描述:290-MHz LOW-DISTORTION HIGH-SPEED AMPLIFIERS |
| THS4011ID | 功能描述:高速運算放大器 290MHz Lw-Distortion RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4011IDG4 | 功能描述:高速運算放大器 290MHz Low-Distort Vltg-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4011IDGN | 功能描述:高速運算放大器 290-MHz Low-Dist Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4011IDGNG4 | 功能描述:高速運算放大器 290-MHz Low-Dist Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。