- 您現在的位置：買賣IC網 > PDF目錄361376 > TC510 (Microchip Technology Inc.) Precision Analog Front Ends PDF資料下載
參數資料
| 型號： | TC510 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | Precision Analog Front Ends |
| 中文描述： | 精密模擬前端 |
| 文件頁數： | 12/17頁 |
| 文件大小： | 209K |
| 代理商： | TC510 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁
3-30
TELCOM SEMICONDUCTOR, INC.
PRECISION ANALOG FRONT ENDS
TC500
TC500A
TC510
TC514
Figure 8. Typical Dual Slope A/D Converter System Timing
AUTO -ZERO
INTEGRATE
FULL SCALE INPUT
REFERENCE
DEINTEGRATE
OVERSHOOT
INTEGRATOR
OUTPUT
ZERO
CONVERTER
STATUS
TIME
INTEGRATOR
VOLTAGE
COMPARATOR
OUTPUT
AB INPUTS
CONTROLLER
OPERATION
NOTES
COMPARATOR DELAY
BEGIN CONVERSION
WITH AUTO-ZERO PHASE
(POSITIVE INPUT SHOWN)
SAMPLE INPUT POLARITY
The length of this phase
is chosen almost arbitrarily
but needs to be long enough
to null out worst case errors
(see text)
MINIMIZING OVERSHOOT
WILL MINIMIZE I.O.Z. TIME
READY FOR NEXT
CONVERSION
(AUTO-ZERO IS IDLE
STATE)
TIME INPUT
INTEGRATION
PHASE
CAPTURE
DEINTEGRATION
TIME
I
NTEGRATOR
OUTPUT
ZERO PHASE
COMPLETE
UNDEFINED
A = 0
B = 1
A = 1
0 FOR NEGATIVE INPUT
1 FOR POSITIVE INPUT
B = 0
B = 1
B = 0
A = 1
A = 0
VINT
TYPICALLY = tINT
tINT
0
A
B
COMPARATOR DELAY +
PROCESSOR LATENCY
is that, during the initial stage of input integration when the
integrator voltage is low, the comparator may be affected by
noise and its output unreliable. Once integration is well
underway, the comparator will be in a defined state.
Reference Deintegration
The length of this phase must be precisely measured
from the transition of AB from 10 to 11 to the falling edge of
CMPTR. The comparator delay contributes some error in
timing this phase. The typical delay is specified to be 2
μ
sec.
This should be considered in the context of the length of a
single count when determining overall system performance
and possible single-count errors. Additionally, Overshoot
will result in charge accumulating on the integrator after its
output crosses zero. This charge must be nulled during the
Integrator Output Zero phase.
Integrator Output Zero phase
The comparator delay and the controller's response
latency may result in Overshoot causing charge buildup on
the integrator at the end of a conversion. This charge must
be removed or performance will degrade. The Integrator
Output Zero phase should be activated (AB = 00) until
CMPTR goes high. It is absolutely critical that this phase be
terminated immediately so that Overshoot is not allowed to
occur in the opposite direction. At this point, it can be
assured that the integrator is near zero. Auto Zero should be
entered (AB = 01) and the TC5xx held in this state until the
next cycle is begun.
相關PDF資料 |
PDF描述 |
|---|---|
| TC510CPF | Precision Analog Front Ends |
| TC514 | Precision Analog Front Ends |
| TC500COE | Precision Analog Front Ends |
| TC510COG | Precision Analog Front Ends |
| TC500 | Precision Analog Front Ends |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC5102-NDT | 制造商:Thomas & Betts 功能描述:TR TC5102NDT LOW PROF CABL TIE MNTG |
| TC5105 | 制造商:Thomas & Betts 功能描述:CABLE TIES |
| TC5-10623156 | 制造商:Spectrah Dynamics 功能描述:- Bulk |
| TC510CJE | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends |
| TC510CO | 功能描述:電信線路管理 IC Precision Analog Front End RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。