- 您現在的位置：買賣IC網 > PDF目錄10750 > TC500IJE (Microchip Technology)IC ANALOG FRONT END 16BIT 16CDIP PDF資料下載
參數資料
| 型號： | TC500IJE |
| 廠商： | Microchip Technology |
| 文件頁數： | 10/38頁 |
| 文件大小： | 0K |
| 描述： | IC ANALOG FRONT END 16BIT 16CDIP |
| 標準包裝： | 29 |
| 位數： | 16 |
| 通道數： | 1 |
| 功率（瓦特）： | 10mW |
| 電壓 - 電源，模擬： | 5V |
| 電壓 - 電源，數字： | 4.5 V ~ 7.5 V |
| 封裝/外殼： | 16-CDIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-CDIP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
TC500/A/510/514
DS21428E-page 18
2008 Microchip Technology Inc.
8.6
Integrator Output Zero Phase
The comparator delay and the controller’s response
latency may result in overshoot, causing charge
buildup on the integrator at the end of a conversion.
This charge must be removed or performance will
degrade. The integrator output zero phase should be
activated (AB = 00) until CMPTR goes high. It is
absolutely critical that this phase be terminated
immediately so that overshoot is not allowed to occur in
the opposite direction. At this point, it can be assured
that the integrator is near zero. Auto-zero should be
entered (AB = 01) and the TC5XX held in this state until
the next cycle is begun (see Figure 8-2).
FIGURE 8-2:
Overshoot.
8.7
Using the TC510/TC514
8.7.1
NEGATIVE SUPPLY VOLTAGE
CONVERTER (TC510, TC514)
A capacitive charge pump is employed to invert the
voltage on VDD for negative bias within the TC510/
TC514. This voltage is also available on the VOUT– pin
to provide negative bias elsewhere in the system. Two
external capacitors are required to perform the
conversion.
Timing is generated by an internal state machine driven
from an on-board oscillator. During the first phase,
capacitor CF is switched across the power supply and
charged to VS+. This charge is transferred to capacitor
COUT– during the second phase. The oscillator
normally runs at 100 kHz to ensure minimum output
ripple. This frequency can be reduced by placing a
capacitor from OSC to VDD. The relationship between
the capacitor value is shown in Section 2.0 “Typical
.
8.7.2
ANALOG INPUT MULTIPLEXER
(TC514)
The TC514 is equipped with a four-input differential
analog multiplexer. Input channels are selected using
select inputs (A1, A0). These are high-true control
signals (i.e., channel 0 is selected when (A1, A0 = 00).
Integrator
Output
Comparator
Output Comp
Integrate
Phase
De-integrate Phase
Integrator
Zero Phase
Zero
Crossing
Overshoot
相關PDF資料 |
PDF描述 |
|---|---|
| MAX919EUK+T | IC COMPARATOR BTR SOT23-5 |
| VI-J32-MY-F3 | CONVERTER MOD DC/DC 15V 50W |
| VI-B6D-MX-F1 | CONVERTER MOD DC/DC 85V 75W |
| VI-J32-MY-F2 | CONVERTER MOD DC/DC 15V 50W |
| VI-B64-MX-F4 | CONVERTER MOD DC/DC 48V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC500IOE | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOE713 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOG | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOG713 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOI | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
發布緊急采購，3分鐘左右您將得到回復。