- 您現在的位置：買賣IC網 > PDF目錄196343 > TB6581HG BRUSHLESS DC MOTOR CONTROLLER, PZIP25 PDF資料下載
參數資料
| 型號： | TB6581HG |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PZIP25 |
| 封裝： | PLASTIC, HZIP-25 |
| 文件頁數： | 13/15頁 |
| 文件大?。?/td> | 410K |
| 代理商： | TB6581HG |
TB6581HG
2008-09-12
7
5.
Setting the carrier frequency
This function sets the triangular wave cycle (carrier cycle) necessary for generating the PWM signal.
(The triangular wave is used for forcibly turning on the lower transistor when the motor is driven by
square wave.)
Carrier cycle
= fosc/254 (Hz)
fosc = reference clock (ceramic oscillation)
6.
Outputting the reverse rotation detection signal
This function detects the motor rotation direction every electrical angle of 360°. This function judges
whether the actual direction of a rotating motor coincides with that of the internal reference voltage.
Actual Motor Rotating Direction
REV Pin
Drive Mode
CW (forward)
HIGH
Square waveform (120° turn-on mode)
CCW (reverse)
LOW
Sine-wave waveform (180° turn-on mode)
*: CW or CCW of the motor is determined by the direction of the Hall signal, which is specified in the timing
chart on page 9.
*: When the REV pin is set to LOW, and the Hall signal is higher than 5 Hz, sine-wave drive mode is turned
on.
7.
Protecting input pin
(1)
Overcurrent protection (Pin Idc)
When the DC-link-current exceeds the internal reference voltage, gate block protection is performed.
Overcurrent protection is released for each carrier frequency.
Reference voltage
= 0.5 V (typ.)
(2)
Positional signal abnormality protection
Output is turned off when the positional signal is HHH or LLL; otherwise, it is restarted.
(3)
Monitor protection for VCC7/ VCC15 low supply voltage
For power supply on/off outside the operating voltage range, the U, V and W drive outputs are
turned off and the motor is stopped when there is a power supply fault.
< VCC7>
< VCC15>
Turn-off drive output
Turn-on drive output
Power supply voltage
4.5 V (typ.)
4.0 V (typ.)
GND
VB
VCC7
Output
Turn-off drive output
Turn-on drive output
Power supply voltage
11.5 V (typ.)
11.0 V (typ.)
GND
VB
VCC15
Turn-off drive output
Output
相關PDF資料 |
PDF描述 |
|---|---|
| TB6591FLG | STEPPER MOTOR CONTROLLER, 0.8 A, PQCC48 |
| TB6674PG | STEPPER MOTOR CONTROLLER, 0.4 A, PDIP16 |
| TBA130-2 | FM SOUND IF FOR TELEVISION APPLICATIONS WITH IC BUS AND SCART |
| TBC1404B | 20 A, BARRIER STRIP TERMINAL BLOCK, 1 DECK |
| TBC1704M | 20 A, BARRIER STRIP TERMINAL BLOCK, 1 DECK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6582FG | 功能描述:馬達/運動/點火控制器和驅動器 Brushless DC Motor Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6582FG(ES) | 制造商:Toshiba America Electronic Components 功能描述: |
| TB6582FG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Brushless DC Motor Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6582FG(OEL) | 制造商:Toshiba America Electronic Components 功能描述:BRUSHLESS DC MOTOR DRIVER 18V 0.2MA |
| TB6584AFNG(O,C8,EL | 功能描述:馬達/運動/點火控制器和驅動器 Brushless Motor DRVR 3-Phase 1A 45V RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。