- 您現在的位置：買賣IC網 > PDF目錄196343 > TB6568KQ BRUSH DC MOTOR CONTROLLER, 3 A, PSIP7 PDF資料下載
參數資料
| 型號： | TB6568KQ |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 3 A, PSIP7 |
| 封裝： | HSIP-7 |
| 文件頁數： | 14/15頁 |
| 文件大小： | 229K |
| 代理商： | TB6568KQ |
8
Package Characteristics
Parameter
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Fig.
Note
Input-Output Momentary
VISO
3750
Vrms
TA = 25°C, RH < 50%
6
Withstand Voltage
Input-Output Resistance
RI-O
>109
VI-O = 500 V
Input-Output Capacitance
CI-O
1.4
pF
Freq = 1 MHz
Notes:
General Note: Typical values were taken from a sample of nominal units operating at nominal conditions (VDD1 = VDD2 = 5 V, VREF = 4.0 V, Temperature =
25°C) unless otherwise stated. Nominal plots shown from Figure 1 to 11 represented the drift of these nominal units from their nominal operating
conditions.
1. Input Offset Voltage is defined as the DC Input Voltage required to obtain an output voltage of VREF/2.
2. Gain is defined as the slope of the best-fit line of the output voltage vs. the differential input voltage (VIN+ - VIN-) over the specified input range. Gain
is derived from VREF/512 mV; e.g. VREF = 5.0, gain will be 9.77 V/V.
3. Nonlinearity is defined as half of the peak-to-peak output deviation from the best-fit gain line, expressed as a percentage of the full-scale output
voltage range.
4. NL200 is the nonlinearity specified over an input voltage range of ±200 mV.
5. NL100 is the nonlinearity specified over an input voltage range of ±100 mV.
6. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage 4500 Vrms for 1 second (leakage detection current
limit, II-O < 5 A). This test is performed before the 100% production test for the partial discharge (method b) shown in
IEC/EN/DIN EN 60747-5-2 Insulation Characteristic Table, if applicable.
7. CMRR is defined as the ratio of the differential signal gain (signal applied differentially between pins 2 and 3) to the common-mode gain (input pins
tied together and the signal applied to both inputs at the same time), expressed in dB.
Switching Specifications (AC)
Over recommended operating conditions unless otherwise specified.
Parameter
Symbol Min.
Typ.
Max.
Units
Test Conditions
Fig. Note
VIN to VOUT Signal Delay (50 – 10%)
tPD10
2.2
4
s
VIN+ = 0 mV to 200 mV step
13
VIN to VOUT Signal Delay (50 – 50%)
tPD50
3.4
5
s
VIN to VOUT Signal Delay (50 – 90%)
tPD90
5.2
9.9
s
VOUT Rise Time (10 – 90%)
tR
3.0
7
s
VOUT Fall Time (10 – 90%)
tF
3.2
7
s
VOUT Bandwidth (-3 dB)
BW
50
100
kHz
VIN+ = 200 mVpk-pk
14
VOUT Noise
NOUT
31.5
mVrms VIN+ = 0 V
Common Mode Transient
CMTI
10
15
kV/s
TA = 25°C, VCM = 1000 V
15
Immunity
相關PDF資料 |
PDF描述 |
|---|---|
| TB6581HG | BRUSHLESS DC MOTOR CONTROLLER, PZIP25 |
| TB6591FLG | STEPPER MOTOR CONTROLLER, 0.8 A, PQCC48 |
| TB6674PG | STEPPER MOTOR CONTROLLER, 0.4 A, PDIP16 |
| TBA130-2 | FM SOUND IF FOR TELEVISION APPLICATIONS WITH IC BUS AND SCART |
| TBC1404B | 20 A, BARRIER STRIP TERMINAL BLOCK, 1 DECK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6568KQ(O) | 制造商:Toshiba America Electronic Components 功能描述: |
| TB6568KQ(O,8) | 功能描述:馬達/運動/點火控制器和驅動器 50V Bridge Drvr for 3A 0.55Ohm PWM RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6569FG | 制造商:Toshiba America Electronic Components 功能描述:IC BRUSHED DC MOTOR DRIVER 50V 5A |
| TB6569FG(O,8,EL | 制造商:Toshiba 功能描述:FULL-BRIDGE DC MOTOR DRIVER IC |
| TB6569FG(O,8,EL) | 功能描述:馬達/運動/點火控制器和驅動器 50V Bridge Drvr for 4.5A PWM ISD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。