參數資料
型號: TA0030
廠商: RF Micro Devices, Inc.
英文描述: TRANSMIT AND RECEIVE AGC AMPLIFIERS FOR CDMA CELLULAR /PCS PHONES
中文描述: 發送和接收AGC放大器的CDMA蜂窩/ PCS電話
文件頁數: 3/6頁
文件大?。?/td> 90K
代理商: TA0030
13-153
TA0030
13
T
A
Copyright 1997-2000 RF Micro Devices, Inc.
The RF2607 features a 96dB gain range from -48dB
power gain to +48dB power gain and is powered from
a single 3.6V supply. As the transmit AGC amplifier is
instructed to adjust its gain, the receive AGC amplifier
will track, so that they work in parallel. As the mobile
strays further from the base station, the RF2607 is
directed to increase its gain while the reverse occurs
as the mobile approaches the base station. The gain of
the IC, like the RF2609, is controlled by a single DC
voltage externally supplied by a digital-to-analog (D/A)
converter which is swept from 0 to 3VDC. Figure 5
illustrates the gain response of the RF2607 as the gain
control voltage is swept.
With this IC, the more demanding specification to meet
is noise figure. In a CDMA receiver, this component fol-
lows the downconverting mixer and must retain good
noise performance at the high end of the gain range. At
the same time the IIP3 must increase steadily as the
gain drops from the high end of the gain range. Using a
variable gain amplifier scheme similar to that used in
the RF2609, both requirements are achievable. At 45
dB gain the RF2607 typically produces a noise figure
of 4.5dB and an IIP3 of -41dBm. Figures 6 and 7 illus-
trate nominal performance of the IC over the entire
gain range.
Incorporating the RF2607 into a system is very simple.
The RF2607 has two input ports, one for CDMA opera-
tion and one for FM operation. This feature allows the
IC to be used in dual mode phones that operate in both
Advanced Mobile Phone Service (AMPS) systems and
IS-95 North American Digital Cellular (NADC) sys-
tems. In dual mode systems, two signal paths are
required at IF in order to filter properly. The CDMA path
requires a filter with a 1.26MHz bandwidth while the
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
10 nF
10 nF
R2:
1 k
C2
C2
L1
C1
L1
C1
V
CC
10 nF
V
CC
CDMA Filter
OUT+
OUT-
IN+
IN-
Measurement
Reference Plane
Z
IN
=1 k
Z
S
=1 k
Z
OUT
=1 k
Z
LOAD
=1 k
R2 sets the balanced output impedance to 1 k
. L1 and C2
serve dual purposes. L1 serves as an output bias choke,
and C2 serves as a series DC block. In addition, the values
of L1 and C2 may be chosen to form an impedance
matching network if the load impedance is not 1k
.
Otherwise, the values of L1 and C1 are chosen to form a
parallel-resonant tank circuit at the IF when the IF filter's
input impedance is 1 k
.
Figure 4. RF2609 Application Circuit
Z
LOAD,EFF
=500
Measurement
Reference Plane
10 nF
10 nF
3.3 k
GAIN
GAIN
CONTROL
RF2607 CDMA Gain vs. Gain Control Voltage
(Vcc=3.6 V, 85 MHz)
-60
-50
-40
-30
-20
-10
0
10
20
30
40
50
60
0.0
0.5
1.0
1.5
2.0
2.5
3.0
GC (volts)
G
+25°C
-30°C
+80°C
Figure 5. RF2607 CDMA Gain vs. Gain Control Voltage
相關PDF資料
PDF描述
TA0038 DC ACCURATE FSK MODULATOR
TA201-BB-B TOGGLE SWITCH, SPST, LATCHED, THROUGH HOLE-STRAIGHT
TC201-BB-W TOGGLE SWITCH, SPDT, LATCHED, THROUGH HOLE-STRAIGHT
TA201-BB-W TOGGLE SWITCH, SPST, LATCHED, THROUGH HOLE-STRAIGHT
TA3FLB 3 CONTACT(S), COPPER, NICKEL PLATED, FEMALE, CIRCULAR CONNECTOR, PLUG
相關代理商/技術參數
參數描述
TA00310001 制造商:SUNON 功能描述:- Bulk
TA003-10001 功能描述:LED HEATSINK W/FAN 12V 60X15MM RoHS:是 類別:光電元件 >> LED LED 散熱產品 系列:- 標準包裝:500 系列:Thermal Clad® IMS® 類型:熱包層板 適用于相關產品:Osram Ostar? 形狀:- 包裝:- 其它名稱:803308-NDBER289
TA00310003 制造商:SUNON 功能描述:- Bulk
TA003-10003 功能描述:LED HEATSINK W/FAN 12V 60X15MM RoHS:是 類別:光電元件 >> LED LED 散熱產品 系列:- 標準包裝:500 系列:Thermal Clad® IMS® 類型:熱包層板 適用于相關產品:Osram Ostar? 形狀:- 包裝:- 其它名稱:803308-NDBER289
TA0038 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:DC ACCURATE FSK MODULATOR