- 您現在的位置：買賣IC網 > PDF目錄383875 > T530X477M006AS (Texas Instruments, Inc.) 60-A, 3.3/5-V INPUT, NONISOLATED WIDE-OUTPUT ADJUST POWER MODULE PDF資料下載
參數資料
| 型號： | T530X477M006AS |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 60-A, 3.3/5-V INPUT, NONISOLATED WIDE-OUTPUT ADJUST POWER MODULE |
| 中文描述： | 60甲，3.3/5-V輸入，非隔離寬輸出調節電源模塊 |
| 文件頁數： | 16/24頁 |
| 文件大小： | 947K |
| 代理商： | T530X477M006AS |
www.ti.com
V
(2V/Div)
O
I
(2
A/Div)
I
Q1Vds(5V/Div)
t-T
ime=10
msec/Div
REMOTE SENSE
Auto-Track FUNCTION
PTH04040W
SLTS238A–SEPTEMBER 2005–REVISED FEBRUARY 2006
Figure 14. Power-Up from Inhibit Control
The remote sense feature allows the regulator to compensate for limited amounts of voltage drop, that may be
incurred between the converter and load, due to resistance in the PCB traces. Connecting the
+Sense
and
–Sense
pins to the respective
V
O
and
GND
output nodes improves the load regulation of the regulator output at
those connection points. This is recommended even if the load circuit is located close to the module.
If either the
+Sense
and
–Sense
are left open-circuit, an internal low-value resistor (15-
or less), connected
from the respective sense pin to either
V
O
or
GND
, ensures the output voltage remains in regulation.
With the sense pins connected, the difference between the voltage measured across the
V
and
GND
pins of the
regulator, and that measured at
+Sense
with respect to
+Sense
, is the amount of IR drop being compensated by
the regulator. This should be limited to a maximum of 0.3 V.
Note: The remote sense feature is not designed to compensate for the forward drop of nonlinear or
frequency dependent components that may be placed in series with the converter output. Examples include
OR-ing diodes, filter inductors, ferrite beads, and fuses. When these components are enclosed by the remote
sense connection they are effectively placed inside the regulation control loop, which can adversely affect the
stability of the regulator.
The Auto-Track function is unique to the PTH/PTV family, and is available with the all POLA-compatible
products. Auto-Track was designed to simplify the amount of circuitry required to make the output voltage from
each module power up and power down in sequence. The sequencing of two or more supply voltages during
power up is a common requirement for complex mixed-signal applications, that use dual-voltage VLSI ICs such
as the TMS320 DSP family, micro-processors, and ASICs.
HOW Auto-Track WORKS
Auto-Track works by forcing the module’s output voltage to follow a voltage presented at the
Track
control pin.
This control range is limited to between 0 V and the module’s set-point voltage. Once the
Track
input is raised
above the set-point voltage, the module’s output remains at its set-point 1. As an example, if the
Track
pin of a
2.5-V regulator is at 1 V, the regulated output will be 1 V. But, if the voltage at the
Track
pin rises to 3 V, the
regulated output does not go higher than 2.5 V.
When the
Track
input is used to connect a number of modules together, it forces the output voltage from each
module to follow a common signal during power-up and power-down. The control signal can be an externally
generated master ramp waveform, or the output voltage from another power supply circuit.
(3)
For convenience,
each module’s
Track
input incorporates an internal RC charge circuit. This operates off the module’s input
voltage to provide a suitable rising voltage ramp waveform.
TYPICAL APPLICATION
Connecting the
Track
inputs of two or more modules forces their
Track
input to follow the same collective RC
ramp waveform, and allows their power-up sequence to be coordinated from a common
Track
control signal.
This can be an open-collector (or open drain) device, such as a power-up reset voltage supervisor IC.
16
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| T5504 | Quad PCM Codecs with Filters(帶濾波器的四PCM編解碼器) |
| T70HF10 | POWER RECTIFIER DIODES |
| T70HF100 | POWER RECTIFIER DIODES |
| T70HF120 | POWER RECTIFIER DIODES |
| T70HF | CONTACTOR? COIL 120VAC NEMA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T530X477M006ASE006 | 功能描述:CAP TANT 470UF 6.3V 20% 2917 RoHS:否 類別:電容器 >> 鉭 系列:KO Cap T530 標準包裝:1,000 系列:TANTAMOUNT® 695D 電容:3.3µF 電壓 - 額定:50V 容差:±20% ESR（等效串聯電阻）:3.2 歐姆 類型:保形涂層 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:2414（6034 公制） 尺寸/尺寸:0.236" L x 0.135" W（6.00mm x 3.43mm） 高度 - 座高（最大）:0.085"（2.16mm） 引線間隔:- 制造商尺寸代碼:F 特點:通用 包裝:帶卷 (TR) 壽命@溫度:- |
| T530X477M006ASE010 | 功能描述:CAP TANT 470UF 6.3V 20% 2917 RoHS:否 類別:電容器 >> 鉭 系列:KO Cap T530 標準包裝:1,000 系列:TANTAMOUNT® 695D 電容:3.3µF 電壓 - 額定:50V 容差:±20% ESR（等效串聯電阻）:3.2 歐姆 類型:保形涂層 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:2414（6034 公制） 尺寸/尺寸:0.236" L x 0.135" W（6.00mm x 3.43mm） 高度 - 座高（最大）:0.085"（2.16mm） 引線間隔:- 制造商尺寸代碼:F 特點:通用 包裝:帶卷 (TR) 壽命@溫度:- |
| T530X477M006AT | 功能描述:鉭質電容器-SMD聚合物 RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
| T530X477M006ATE | 功能描述:鉭質電容器-SMD聚合物 470uF 6volts 20% RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
| T530X477M006ATE004 | 功能描述:鉭質電容器-SMD聚合物 470uF 6.3 Volts 20% ESR = 4 mOhms RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。