th July 2011 36 www.semtech.com SX8657/SX8658 Haptics " />
參數資料
型號: SX8658IWLTRT
廠商: Semtech
文件頁數: 30/61頁
文件大?。?/td> 0K
描述: IC TOUCH SCREEN 12BIT 20QFN
標準包裝: 1
類型: 電阻式,觸感驅動器
觸摸面板接口: 4,5 線
輸入數/鍵: 1 TSC,雨刷,鑰匙
分辨率(位): 12 b
評估套件: *
數據接口: I²C,串行
電壓基準: 內部
電源電壓: 2.3 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-WFQFN 裸露焊盤
供應商設備封裝: 20-QFN(4x4)
包裝: 標準包裝
其它名稱: SX8658IWLDKR
ADVANCED COMMUNICATIONS & SENSING
Rev 1 – 25
th July 2011
36
www.semtech.com
SX8657/SX8658
Haptics Enabled 4/5-Wire
Resistive Touchscreen Controller with Proximity Sensing
A
cc
el
er
at
in
g
Figure 46 – ERM Drive Signal Example
If AmplitudeCode is within HAPTSQUELCH range (for more than 512/MIN_Freq in PWM mode, for more than
512/FOSCL in I2C mode):
VMOUT = 0V
Else:
VMOUT(V) = (AmplitudeCode / 127) x 1.135 * HAPTGAIN
AmplitudeCode (signed) is defined differently depending on the mode selected (PWM or I2C), see below.
Please note that whatever setting, VMOUT is physically limited to [MVDD;-MVDD], i.e. saturation effect.
6.2.2
PWM Mode
PWM mode is selected when HAPTMODE = 0.
In this mode, AmplitudeCode is extracted/updated at each MIN period from MIN_DutyCycle:
MIN_DutyCycle
≈ 0% => AmplitudeCode = -127
MIN_DutyCycle = 49.6% => AmplitudeCode = -1
MIN_DutyCycle = 50% => AmplitudeCode = 0
MIN_DutyCycle = 50.4% => AmplitudeCode = +1
MIN_DutyCycle
≈ 100% => AmplitudeCode = +127
6.2.3
I2C Mode
I2C mode is selected when HAPTMODE = 1.
In this mode, AmplitudeCode = HAPTAMP (signed, internally sampled at FOSCL). MIN is not used and should
be grounded. HAPTRANGE must be set to 1.
6.3
LRA Load
6.3.1
Introduction
An LRA is a spring and mass with an electro-magnetic coil to move the mass. It is operated by applying an AC
signal at its resonant frequency (typ. ~175 Hz). Like pushing a swing at its resonance, it doesn’t need much
energy to keep it going, so drive current requirements are much lower than for ERMs. LRAs have moderately
high Q factors so that the drive frequency must match the resonant frequency within a few Hz to get optimum
amplitude.
LRA load is selected when HAPTTYPEEN = 01.
相關PDF資料
PDF描述
VE-20R-MX-F4 CONVERTER MOD DC/DC 7.5V 75W
SX8655IWLTRT IC TOUCH SCREEN 12BIT 20QFN
LDS6128NQGI8 IC SENSOR TCH PURETOUCH 40VFQFPN
LDS6104NQGI8 IC SENSOR TCH PURETOUCH 28VFQFPN
D38999/24WG39SC CONN RCPT 39POS JAM NUT W/SCKT
相關代理商/技術參數
參數描述
SX8660 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Ultra Low Power, Capacitive Button Touch Controller (8 sensors) with Enhanced LED Drivers and Analog Output
SX8660I06AULTRT 制造商:Semtech Corporation 功能描述:Touch Controller with Enhanced LED Drivers 28-Pin MLPQ-UT EP T/R 制造商:Semtech Corporation 功能描述:TOUCH SCREEN CONTROLLER 制造商:Semtech Corporation 功能描述:IC CAP BUTTON TOUCH PROXIMITY CTRL MLP 制造商:Semtech Corporation 功能描述:SX8660 Series 3.6 V Ultra Low Power Capacitive Button Touch Controller-MLPQ-UT28 制造商:Semtech Corporation 功能描述:IC, CAP BUTTON TOUCH PROXIMITY CTRL, MLPQ-28; Controller Type:Capacitive Touch Screen; IC Interface Type:I2C; Supply Voltage Min:2.7V; Supply Voltage Max:3.6V; Digital IC Case Style:MLPQ; No. of Pins:28; No. of Channels:8 制造商:Semtech Corporation 功能描述:IC, CAP BUTTON TOUCH CTRL, 8 SENSOR, MLPQ-28; Controller Type:Capacitive Touch Screen; IC Interface Type:I2C; Supply Voltage Min:2.7V; Supply Voltage Max:3.6V; Digital IC Case Style:MLPQ; No. of Pins:28; No. of Channels:8 制造商:SEMTECH 功能描述:Sensor
SX8660I06YULTRT 制造商:Semtech Corporation 功能描述:Sensor
SX8660I06ZULT 制造商:Semtech Corporation 功能描述:TAPE & REEL VCO
SX8660I06ZULTRT 制造商:Semtech Corporation 功能描述:8-CH CAPACITIVE TOUCH SOLUTION