th July 2011 19 www.semtech.com SX8654/SX8655/SX8656 H" />
參數資料
型號: SX8656IWLTRT
廠商: Semtech
文件頁數: 11/62頁
文件大?。?/td> 0K
描述: IC TOUCH SCREEN 12BIT 20QFN
標準包裝: 1
類型: 電阻式,觸感驅動器
觸摸面板接口: 4,5 線
輸入數/鍵: 1 TSC,雨刷,鑰匙
分辨率(位): 12 b
評估套件: *
數據接口: I²C,串行
電壓基準: 內部
電源電壓: 2.3 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-WFQFN 裸露焊盤
供應商設備封裝: 20-QFN(4x4)
包裝: 標準包裝
其它名稱: SX8656IWLDKR
ADVANCED COMMUNICATIONS & SENSING
Rev 1 – 25
th July 2011
19
www.semtech.com
SX8654/SX8655/SX8656
Haptics Enabled 4/5-Wire
Resistive Touchscreen Controller with Proximity Sensing
4.6
Host Operation
4.6.1
Overview
The chip has three operating modes that are configured using the I2C as defined in §11 :
Manual (command ‘MAN’ and TOUCHRATE = 0).
Pen detect (command ‘PENDET’ and TOUCHRATE > 0).
Pen trigger (command ‘PENTRG’ and TOUCHRATE > 0).
At power-up the chip is set in manual mode.
4.6.2
Manual Mode (MAN)
In manual mode (MAN) the touchscreen interface is stopped and conversions must be manually triggered by the
host using SELECT and CONVERT command.
When a command is received, the chip executes the associated tasks listed in table below and waits for the next
command. It is up to the host to sequence all actions.
Pen detection is performed after each CONVERT command and if pen is not detected, no touch operation is
performed. Following figures assume pen down. PENSTAT is not updated in MAN mode.
To enter MAN mode the host must send the MAN command and then set TOUCHRATE = 0.
Command
Actions
CONVERT(CHAN)
Select and bias CHAN
Wait for the programmed settling time (POWDLY)
Convert CHAN
SELECT(CHAN)
Select and bias CHAN
Table 6 – Manual Mode Commands
As illustrated in figure below the CONVERT command will bias the channel, wait for the programmed settling
time (POWDLY), and run the conversion.
Figure 19 – Manual Mode – CONVERT Command (CHAN = Y; PROXSCANPERIOD = 0)
When the CONVERT command is used with CHAN=SEQ, multiple channels as defined in RegChnMsk are
sampled. In this case, each channel will be sequentially biased during POWDLY before a conversion is started.
At the end of each channel conversion the bias is automatically removed.
Figure 20 – Manual Mode – CONVERT Command (CHAN = SEQ = [X;Y]; PROXSCANPERIOD = 0)
I2C
Channel Bias
CONVERT(SEQ)
Channel Conversion
READ CHANNEL
POWDLY
Y
X
NIRQ (RegIrqMsk[3]=1)
CONVSTAT
I2C
Channel Bias
CONVERT(Y)
Channel Conversion
READ CHANNEL
NIRQ (RegIrqMsk[3]=1)
POWDLY
Y
CONVSTAT
相關PDF資料
PDF描述
VE-24D-MX-F2 CONVERTER MOD DC/DC 85V 75W
MS3452W14S-7PY CONN RCPT 3POS BOX MNT W/PINS
MS27474T24B61SA CONN RCPT 61POS JAM NUT W/SCKT
D38999/24WE6SE CONN RCPT 6POS JAM NUT W/SCKT
D38999/24JC8JN CONN RCPT 8POS JAM NUT W/SCKT
相關代理商/技術參數
參數描述
SX8657 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Haptics Enabled 4/5-Wire Resistive Touchscreen Controller with Proximity Sensing
SX8657ICSTRT 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Haptics Enabled 4/5-Wire Resistive Touchscreen Controller with Proximity Sensing
SX8657IWLTRT 功能描述:IC TOUCH SCREEN 12BIT 20QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率(位):- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS,BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
SX8658ICSTRT 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Haptics Enabled 4/5-Wire Resistive Touchscreen Controller with Proximity Sensing
SX8658IWLTRT 功能描述:IC TOUCH SCREEN 12BIT 20QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率(位):- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS,BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)