參數資料
型號: STPCI2
英文描述: STPC ATLAS DATASHEET / X86 CORE PC COMPATIBLE SYSTEM-ON-CHIP FOR TERMINALS
中文描述: STPC阿特拉斯部件/ x86內核PC兼容的系統單芯片貨柜碼頭
文件頁數: 37/71頁
文件大?。?/td> 1071K
代理商: STPCI2
ELECTRICAL SPECIFICATIONS
Issue 2.4 - February 11, 2002
37/69
4 ELECTRICAL SPECIFICATIONS
4.1 INTRODUCTION
The electrical specifications in this chapter are
valid for the STPC Industrial.
4.2 ELECTRICAL CONNECTIONS
4.2.1 Power/Ground Connections/Decoupling
Due to the high frequency of operation of the
STPC Industrial, it is necessary to install and test
this device using standard high frequency
techniques. The high clock frequencies used in
the STPC Industrial and its output buffer circuits
can cause transient power surges when several
output buffers switch output levels simultaneously.
These effects can be minimized by filtering the
DC power leads with low-inductance decoupling
capacitors, using low impedance wiring, and by
utilizing all of the VSS and VDD pins.
4.2.2 Unused Input Pins
All inputs not used by the designer and not listed
in the table of pin connections in
Section 2
should
be connected either to VDD or to VSS. Connect
active-high inputs to VDD through a 20 k
(±10%) pull-down resistor and active-low inputs to
VSS and connect active-low inputs to VCC
through a 20 k
(±10%) pull-up resistor to prevent
spurious operation.
4.2.3 Reserved Designated Pins
Pins designated
disconnected. Connecting a reserved pin to a
pull-up resistor, pull-down resistor, or an active
signal could cause unexpected results and
possible circuit malfunctions.
reserved
should be
left
4.3 ABSOLUTE MAXIMUM RATINGS
The following table lists the absolute maximum
ratings for the STPC Industrial device. Stresses
beyond those listed under
Table 4-1
limits may
cause permanent damage to the device. These
are stress ratings only and do not imply that
operation under any conditions other than those
specified in section "Operating Conditions".
Exposure to conditions beyond those outlined in
Table 4-1
may (1) reduce device reliability and (2)
result in premature failure even when there is no
immediately apparent sign of failure. Prolonged
exposure to conditions at or near the absolute
maximum ratings (
Table 4-1
) may also result in
reduced useful life and reliability.
Table 4-1. Absolute Maximum Ratings
Symbol
V
DDx
V
I
, V
O
V
5T
V
ESD
T
STG
T
OPER
P
TOT
Parameter
Minimum
-0.3
-0.3
2.5
Maximum
4.0
VDD + 0.3
5.5
1500
+150
+115
4.8
Units
V
V
V
V
°C
°C
W
DC Supply Voltage
Digital Input and Output Voltage
5Volt Tolerance
ESD Capacity (Human body mode)
Storage Temperature
Operating Temperature
Maximum Power Dissipation
-40
-40
-
相關PDF資料
PDF描述
STPCI2GDYI PERIPHERAL (MULTIFUNCTION) CONTROLLER
STPCI2HDYC PERIPHERAL (MULTIFUNCTION) CONTROLLER
STPCI2HEYI PERIPHERAL (MULTIFUNCTION) CONTROLLER
STPQ1NC60R TRANSISTOR | MOSFET | N-CHANNEL | 600V V(BR)DSS | 300MA I(D) | TO-92
STPT3091 Low Current Operation at 250 ,Low Reverse Leakage,Low Noise Zener Diode
相關代理商/技術參數
參數描述
STPCI2GDY 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:X86 Core PC Compatible System-on-Chip for Terminals
STPCI2GDYI 功能描述:微處理器 - MPU 120MHz x86 SoC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
STPCI2GDYIE 制造商:STMicroelectronics 功能描述:
STPCI2HDYC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PERIPHERAL (MULTIFUNCTION) CONTROLLER
STPCI2HEYC 功能描述:微處理器 - MPU 133MHz x86 SoC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324