- 您現在的位置：買賣IC網 > PDF目錄372313 > ST92185 16K/24K/32K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY PDF資料下載
參數資料
| 型號： | ST92185 |
| 英文描述： | 16K/24K/32K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY |
| 中文描述： | 16K/24K/32K光盤HCMOS微控制器屏幕顯示器 |
| 文件頁數： | 192/230頁 |
| 文件大小： | 2743K |
| 代理商： | ST92185 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁當前第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁
192/230
ST92163 - I2C BUS INTERFACE
I
2
C BUS INTERFACE
(Cont’d)
I
2
C STATUS REGISTER 2 (I2CSR2)
R242 - Read Only
Register Page: 20
Reset Value: 0000 0000 (00h)
Note:
Some bits of this register are reset by a read
operation of the register. Care must be taken when
using instructions that work on single bit. Some of
them perform a read of all the bits of the register
before modifying or testing the wanted bit. So oth-
er bits of the register could be affected by the op-
eration.
In the same way, the test/compare operations per-
form a read operation.
Moreover, if some interrupt events occur while the
register is read, the corresponding flags are set,
and correctly read, but if the read operation resets
the flags, no interrupt request occurs.
Bits 7:6 = Reserved. Forced to 0 by hardware.
Bit 5 =
ADDTX
Address or 2nd header transmitted
in Master mode.
This bit is set by hardware when the peripheral,
enabled in Master mode, has received the ac-
knowledge relative to:
– Address byte in 7-bit mode
– Address or 2nd header byte in 10-bit mode.
0: No address or 2nd header byte transmitted
1: Address or 2nd header byte transmitted.
Bit 4 =
AF
Acknowledge Failure
.
This bit is set by hardware when no acknowledge
is returned. An interrupt is generated if ITE=1.
It is cleared by software reading I2CSR2 register
after the falling edge of the acknowledge SCL
pulse
, or by hardware when the interface is disa-
bled (I2CCR.PE=0).
The SCL line is not held low while AF=1.
0: No acknowledge failure detected
1: A data or address byte was not acknowledged
Bit 3 =
STOPF
Stop Detection (Slave mode).
This bit is set by hardware when a Stop condition
is detected on the bus after an acknowledge. An
interrupt is generated if ITE=1.
It is cleared by software reading I2CSR2 register
or by hardware when the interface is disabled
(I2CCR.PE=0).
The SCL line is not held low while STOPF=1.
0: No Stop condition detected
1: Stop condition detected (
while slave receiver
)
Bit 2 =
ARLO
Arbitration Lost
.
This bit is set by hardware when the interface (in
master mode) loses the arbitration of the bus to
another master. An interrupt is generated if ITE=1.
It is cleared by software reading I2CSR2 register
or by hardware when the interface is disabled
(I2CCR.PE=0).
After an ARLO event the interface switches back
automatically to Slave mode (M/SL=0).
The SCL line is not held low while ARLO=1.
0: No arbitration lost detected
1: Arbitration lost detected
Bit 1 =
BERR
Bus Error.
This bit is set by hardware when the interface de-
tects a Start or Stop condition during a byte trans-
fer. An interrupt is generated if ITE=1.
It is cleared by software reading I2CSR2 register
or by hardware when the interface is disabled
(I2CCR.PE=0).
The SCL line is not held low while BERR=1.
Note
: If a misplaced start condition is detected,
also the
ARLO
flag is set; moreover, if a misplaced
stop condition is placed on the acknowledge SCL
pulse, also the
AF
flag is set.
0: No Start or Stop condition detected during byte
transfer
1: Start or Stop condition detected during byte
transfer
Bit 0 =
GCAL
General Call address matched.
This bit is set by hardware after an address
matches with the value stored in the I2CADR reg-
ister while ENGC=1. In the I2CADR the General
Call address must be placed before enabling the
peripheral.
It is cleared by hardware after the detection of a
Stop condition, or when the peripheral is disabled
(I2CCR.PE=0).
0: No match
1: General Call address matched.
7
0
0
0
ADDTX
AF
STOPF ARLO
BERR
GCAL
相關PDF資料 |
PDF描述 |
|---|---|
| ST92186B | 8/16-BIT MCU FOR TV APPLICATIONS WITH UP TO 32K ROM AND ENHANCED ON-SCREEN-DISPLAY |
| ST92T163N4B1L | 8/16-BIT FULL SPEED USB MCU FOR COMPOSITE DEVICES WITH 16 ENDPOINTS. 20K ROM. 2K RAM. I 2 C. SCI. & MFT |
| ST92E195 | 48-96 KBYTE ROM HCMOS MCU WITH ON-SCREEN DISPLAY AND TELETEXT DATA SLICER |
| ST92F120JV1 | 8/16-BIT FLASH MCU FAMILY WITH RAM. EEPROM AND J1850 BLPD |
| ST92F120JV9 | 8/16-BIT FLASH MCU FAMILY WITH RAM. EEPROM AND J1850 BLPD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST92185B | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16K/24K/32K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY |
| ST92185B1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16K/24K/32K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY |
| ST92185B1BJ1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16K/24K/32K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY |
| ST92185B1BN1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16K/24K/32K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY |
| ST92185B1T1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16K/24K/32K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY |
發布緊急采購，3分鐘左右您將得到回復。