- 您現在的位置：買賣IC網 > PDF目錄383840 > ST7LITE10F1B6 ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI PDF資料下載
參數資料
| 型號： | ST7LITE10F1B6 |
| 英文描述： | ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| 中文描述： | ST7LITE1 - 8單電壓閃存EEPROM的MEMORY.DATA位MCU。 ADC的。 4定時器。的SPI |
| 文件頁數： | 47/122頁 |
| 文件大?。?/td> | 1716K |
| 代理商： | ST7LITE10F1B6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
ST7LITE0, ST7SUPERLITE
47/122
LITE TIMER
(Cont’d)
11.1.3 Functional Description
The value of the 8-bit counter cannot be read or
written by software. After an MCU reset, it starts
incrementing from 0 at a frequency of f
OSC
/32. A
counter overflow event occurs when the counter
rolls over from F9h to 00h. If f
OSC
= 8 MHz, then
the time period between two counter overflow
events is 1 ms. This period can be doubled by set-
ting the TB bit in the LTCSR register.
When the timer overflows, the TBF bit is set by
hardware and an interrupt request is generated if
the TBIE is set. The TBF bit is cleared by software
reading the LTCSR register.
11.1.3.1 Watchdog
The watchdog is enabled using the WDGE bit.
The normal Watchdog timeout is 2ms (@ = 8 MHz
f
OSC
), after which it then generates a reset.
To prevent this watchdog reset occuring, software
must set the WDGD bit. The WDGD bit is cleared
by hardware after t
WDG
. This means that software
must write to the WDGD bit at regular intervals to
prevent a watchdog reset occurring. Refer to
Fig-
ure 31
.
If the watchdog is not enabled immediately after
reset, the first watchdog timeout will be shorter
than 2ms, because this period is counted starting
from reset. Moreover, if a 2ms period has already
elapsed after the last MCU reset, the watchdog re-
set will take place as soon as the WDGE bit is set.
For these reasons, it is recommended to enable
the Watchdog immediately after reset or else to
set the WDGD bit before the WGDE bit so a
watchdog reset will not occur for at least 2ms.
Note:
Software can use the timebase feature to
set the WDGD bit at 1 or 2 ms intervals.
A Watchdog reset can be forced at any time by
setting the WDGRF bit. To generate a forced
watchdog reset, first watchdog has to be activated
by setting the WDGE bit and then the WDGRF bit
has to be set.
The WDGRF bit also acts as a flag, indicating that
the Watchdog was the source of the reset. It is au-
tomatically cleared after it has been read.
Caution:
When the WDGRF bit is set, software
must clear it, otherwise the next time the watchdog
is enabled (by hardware or software), the micro-
controller will be immediately reset.
Hardware Watchdog Option
If Hardware Watchdog is selected by option byte,
the watchdog is always active and the WDGE bit in
the LTCSR is not used.
Refer to the Option Byte description in the "device
configuration and ordering information" section.
Using Halt Mode with the Watchdog (option)
If the Watchdog reset on HALT option is not se-
lected by option byte, the Halt mode can be used
when the watchdog is enabled.
In this case, the HALT instruction stops the oscilla-
tor. When the oscillator is stopped, the Lite Timer
stops counting and is no longer able to generate a
Watchdog reset until the microcontroller receives
an external interrupt or a reset.
If an external interrupt is received, the WDG re-
starts counting after 256 CPU clocks. If a reset is
generated, the Watchdog is disabled (reset state).
If Halt mode with Watchdog is enabled by option
byte (No watchdog reset on HALT instruction), it is
recommended before executing the HALT instruc-
tion to refresh the WDG counter, to avoid an unex-
pected WDG reset immediately after waking up
the microcontroller.
1
相關PDF資料 |
PDF描述 |
|---|---|
| ST7LITE10F1M6 | FUSE PULLER/TESTERFUSE PULLER/TESTER; Depth, external:15mm; Length:60mm; Voltage rating, AC:24V; Voltage rating, DC:24V; Width, external:20mm |
| ST7LITE15F1B6 | CLIP FUSE 10A 5X20MM PC MOUNT |
| ST7LITE15F1M6 | CLIP FUSE 15A VERT ATO PC MOUNT |
| ST7LITE19F1B6 | FUSE CLIP 3AG SLDR LUG TIN BRASS |
| ST7LITE19F1M6 | ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST7LITE10F1M6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| ST7LITE15F1B6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| ST7LITE15F1M6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| ST7LITE19F1B6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| ST7LITE19F1M6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
發布緊急采購，3分鐘左右您將得到回復。