- 您現在的位置：買賣IC網 > PDF目錄1970 > ST78C36ACJ44-F (Exar Corporation)IC UART FIFO 16B 44PLCC PDF資料下載
參數資料
| 型號： | ST78C36ACJ44-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 25/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 16B 44PLCC |
| 標準包裝： | 27 |
| 特點： | * |
| FIFO's： | 16 字節 |
| 規程： | 打印機 |
| 電源電壓： | 5V |
| 帶并行端口： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁
ST78C36/36A
7
REV. 5.1.0
ECP/EPP PARALLEL PRINTER PORT WITH 16-BYTE FIFO
3.4
CONTROL REGISTER ( DCR )
DCR Bit-0:
The complement of this bit drives -STROBE, and the complement of the pad state is returned for read.
DCR Bit-1:
The complement of this bit drives -AUTOFD, and the complement of the pad state is returned for read.
DCR Bit-2:
This bit drives INIT, and the pad state is returned for read.
DCR Bit-3:
The complement of this bit drives -SLCTIN, and the complement of the pad state is returned for read.
DCR Bit-4:
Ack Interrupt Enable set to a high will generate an interrupt when -ACK is low. When either returns to a high
state, this interrupt source will go in-active. This interrupt is not pulsed.
DCR Bit-5:
Peripheral port direction, OUT = 0 and IN = 1.
This bit is forced to logic zero by ECR modes 000 or 010. It can be written only in ECR mode 001, and will
maintain that state if the ECR mode is changed to 011, 100, or 110. This bit must be set low for EPP mode,
which allows the host to control direction with -IOR and -IOW. The final port direction also drives PDIR.
DCR Bits 6-7:
Reserved, logic zero.
3.5
EPP ADDRESS PORT ( EPP-APort )
When EPP mode is enabled, a host read or write with this port will result in a data transfer directly to/from the
peripheral with -SLCTIN active. Direction is set by host read/write and will drive -STROBE low during a write if
DCR bit 5 (DIR) is not set high.
3.6
EPP DATA PORT (EPP-DPort )
When EPP mode is enabled, a host read or write with this port will result in a data transfer directly to/from the
peripheral with -AUTOFD active. Direction is set by host read/write and will drive -STROBE low during a write
if DCR bit 5 (DIR) is not set high.
3.7
PARALLEL PORT DATA ( C-FIFO )
This port is available for programmed I/O and DMA access. Data written to this port is stored in the FIFO if
FIFO-F = 0 and will be lost if FIFO-F = 1.
Data written to this port will be automatically transferred to the peripheral with -STROBE handshaking with
BUSY. This port is only defined for write, host reads will interfere with FIFO read sequencing.
3.8
ECP DATA FIFO ( ECP-DFIFO )
This port is available for programmed I/O and DMA access. Data written to this port is stored in the FIFO if
FIFO-F = 0 and will be lost if FIFO-F = 1. A 9th FIFO bit (tag) is set high on write.
Data read from this port will undergo de-compression if the FIFO tag bit and data bit-7 are both low. The byte
containing the RLE count is loaded into the RLE counter and the succeeding byte in the FIFO will be returned
to the host RLE count + 1 times before the FIFO read address is incremented. If a FIFO under-run is incurred
during host read, the last data byte is returned and FIFO-E remains coherent.
相關PDF資料 |
PDF描述 |
|---|---|
| SW06GSZ-REEL | IC SWITCH QUAD SPST 16SOIC |
| SX1501I087TRT | IC GPIO EXPANDER I2C 4CH 20QFN |
| SX1504I087TRT | IC GPIO EXPANDER I2C 4CH 20QFN |
| SX1509BULTRT | IC GPIO EXPANDER I2C 16CH 28QFN |
| SX8722I070TRLF | IC ZOOMING ADC 10BIT 16CH 44MLPQ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST78C36ACJ44TR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 16Byte FIFO 5V 44-Pin PLCC T/R 制造商:Exar Corporation 功能描述:ST78C36ACJ44TR-F |
| ST78C36CJ-0A-EVB | 功能描述:界面開發工具 Supports 78C36 44 ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| ST78C36CJ44 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral Interface |
| ST78C36CJ44F | 制造商:N/A 功能描述:NEW |
| ST78C36CJ44-F | 功能描述:接口 - 專用 UART RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。