- 您現在的位置：買賣IC網 > PDF目錄383839 > ST78C34CJ44 (EXAR CORP) GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO PDF資料下載
參數資料
| 型號： | ST78C34CJ44 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
| 中文描述： | 8 I/O, PIA-PRINTER INTERFACE, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 8/21頁 |
| 文件大小： | 198K |
| 代理商： | ST78C34CJ44 |
6-10
ST78C34
Rev. 3.00
COM BIT-2:
INIT input pin.
0= INIT pin is in low state
1= INIT pin is in high state
COM BIT-3:
-SLCTIN input pin.
0= -SLCTIN pin is in high state
1= -SLCTIN pin is in low state
COM BIT-4:
Interrupt mask.
0= Interrupt (INT output) is disabled
1= Interrupt (INT output) is enabled
COM BIT 7-5:
Not used. Are set to “1” permanently.
CONTROL REGISTER.
Writing to this register will set the state of the -
STROBE, -AUTOFDXT, INIT, SLCTIN pins, and in-
terrupt mask register.
CON BIT-0:
-STROBE output control bit.
0= -STROBE output is set to high state
1= -STROBE output is set to low state
CON BIT-1:
-AUTOFDXT output control bit.
0= -AUTOFDXT output is set to high state
1= -AUTOFDXT output is set to low state
CON BIT-2:
INIT output control bit.
0= INIT output is set to low state
1= INIT output is set to high state
CON BIT-3:
-SLCTIN output control bit.
0= -SLCTIN output is set to high state
1= -SLCTIN output is set to low state
CON BIT-4:
Interrupt output control bit.
0= INT output is disabled (three state mode)
1= INT output is enabled
CON BIT-5:
I/O select. Direction of the PD7-PD0 can be selected
by setting or clearing this bit.
0= PD7-PD0 are set for output mode
1= PD7-PD0 are set for input mode
CON BIT 7-6:
Not used.
ALTERNATE FUNCTION REGISTER (AFR)
This register En/Disables FIFO operation and pro-
vides additional capabilities to control -STROBE. INT
and change interrupt functions.
AFR BIT 0-2:
Timing select.
The -STROBE delay and width can be controlled by
these bits.
AFR
Bit-2
AFR
Bit-1
AFR
Bit-0
TSD
(clocks)
TSW
(clocks)
1
1
1
1
0
0
0
0
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
3
5
5
9
6
10
10
18
2
4
4
8
4
8
8
16
AFR BIT-3:
Interrupt source.
0= -ACK input pin is selected as printer handshaking
source
1= BUSY input pin is selected as printer handshaking
source
AFR BIT 4-5:
Interrupt type. State of the INT output pin can be
selected for one of the following options.
相關PDF資料 |
PDF描述 |
|---|---|
| ST78C34CP40 | GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
| ST78C34IJ44 | GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
| ST78C34IP40 | GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
| ST78C36 | ECP/EPP Parallel Printer Port with 16 Byte FIFO(ECP/EPP并行打印機端口（帶16字節先進先出）) |
| ST78C36A | ECP/EPP Parallel Printer Port with 16 Byte FIFO(ECP/EPP并行打印機端口（帶16字節先進先出）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST78C34CJ44-F | 功能描述:輸入/輸出控制器接口集成電路 INTERNAL FIFO UART RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ST78C34CJ44TR-F | 制造商:Exar Corporation 功能描述:ST78C34CJ44TR-F |
| ST78C34CP40 | 功能描述:輸入/輸出控制器接口集成電路 Gen Purpose Parallel Printer Port RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ST78C34CP40-F | 功能描述:輸入/輸出控制器接口集成電路 INTERNAL FIFO UART RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ST78C34IJ44 | 制造商:EXAR 制造商全稱:EXAR 功能描述:GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。