參數資料
型號: ST72C254G2M1
英文描述: 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY. ADC. 16-BIT TIMERS. SPI.
中文描述: 8位單電壓閃存微控制器。 ADC的。 16位定時器。的SPI。
文件頁數: 104/140頁
文件大?。?/td> 1349K
代理商: ST72C254G2M1
ST72104G, ST72215G, ST72216G, ST72254G
66/140
SERIAL PERIPHERAL INTERFACE (Cont’d)
12.3.4.4 Write Collision Error
A write collision occurs when the software tries to
write to the DR register while a data transfer is tak-
ing place with an external device. When this hap-
pens, the transfer continues uninterrupted; and
the software write will be unsuccessful.
Write collisions can occur both in master and slave
mode.
Note: a "read collision" will never occur since the
received data byte is placed in a buffer in which
access is always synchronous with the MCU oper-
ation.
In Slave mode
When the CPHA bit is set:
The slave device will receive a clock (SCK) edge
prior to the latch of the first data transfer. This first
clock edge will freeze the data in the slave device
DR register and output the MSBit on to the exter-
nal MISO pin of the slave device.
The SS pin low state enables the slave device but
the output of the MSBit onto the MISO pin does
not take place until the first data transfer clock
edge.
When the CPHA bit is reset:
Data is latched on the occurrence of the first clock
transition. The slave device does not have any
way of knowing when that transition will occur;
therefore, the slave device collision occurs when
software attempts to write the DR register after its
SS pin has been pulled low.
For this reason, the SS pin must be high, between
each data byte transfer, to allow the CPU to write
in the DR register without generating a write colli-
sion.
In Master mode
Collision in the master device is defined as a write
of the DR register while the internal serial clock
(SCK) is in the process of transfer.
The SS pin signal must be always high on the
master device.
WCOL bit
The WCOL bit in the SR register is set if a write
collision occurs.
No SPI interrupt is generated when the WCOL bit
is set (the WCOL bit is a status flag only).
Clearing the WCOL bit is done through a software
sequence (see Figure 41).
Figure 41. Clearing the WCOL bit (Write Collision Flag) Software Sequence
Clearing sequence after SPIF = 1 (end of a data byte transfer)
1st Step
Read SR
Read DR
Write DR
2nd Step
SPIF =0
WCOL=0
SPIF =0
WCOL=0 if no transfer has started
WCOL=1 if a transfer has started
Clearing sequence before SPIF = 1 (during a data byte transfer)
1st Step
2nd Step
WCOL=0
before the 2nd step
Read SR
Read DR
Note: Writing in DR register in-
stead of reading in it do not reset
WCOL bit
Read SR
OR
THEN
相關PDF資料
PDF描述
ST72C254G2E0 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY. ADC. 16-BIT TIMERS. SPI.
ST72C104G2M7 1GB DDR3 SDRAM SODIMM
ST72C104G2M6 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY. ADC. 16-BIT TIMERS. SPI.
ST72C104G2M5 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY. ADC. 16-BIT TIMERS. SPI.
ST72C104G2M3 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY. ADC. 16-BIT TIMERS. SPI.
相關代理商/技術參數
參數描述
ST72C254G2M3 功能描述:8位微控制器 -MCU ST72104G ST72215G ST72254G 8B MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72C254G2M3/TR 功能描述:8位微控制器 -MCU 8B MCU SINGLE VLTG FLASH MEMORY RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72C254G2M6 功能描述:8位微控制器 -MCU Flash 8K SPI/I2C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72C254G2M6 制造商:STMicroelectronics 功能描述:8BIT MCU FLASH 8K 72C254 SOIC28
ST72C254G2M6/TR 制造商:ST 功能描述:0