參數資料
型號: ST62T18CM3
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO20
封裝: 0.300 INCH, PLASTIC, SOP-20
文件頁數: 49/82頁
文件大小: 937K
代理商: ST62T18CM3
Obsolete
Product(s)
- Obsolete
Product(s)
53/82
ST62T18C/E18C
4.5 U. A. R. T. (Universal Asynchronous Receiver/Transmitter)
The UART provides the basic hardware for asyn-
chronous serial communication which, combined
with an appropriate software routine, gives a serial
interface providing communication with common
baud rates (up to 76,800 Baud with an 8MHz ex-
ternal oscillator) and flexible character formats.
Operating in Half-Duplex mode only, the UART
uses a 10-bit frame or a 11-bit frame according to
the choosen MCU option. Automatic parity bit gen-
eration is software selectable in the 10-bit charac-
ter format allowing either 7 data bit + 1 parity bit, or
8 data bit transmission. Transmitted data is sent di-
rectly, while received data is buffered allowing fur-
ther data characters to be received while the data
is being read out of the receive buffer register. Data
transmit has priority over data being received.
The UART is supplied with an MCU internal clock
that is also available in WAIT mode of the processor.
4.5.1 Ports Interfacing
RXD reception line and TXD emission line are
sharing the same external pins as two I/O lines.
Therefore, UART configuration requires to set
these two I/O lines through the relevant ports reg-
isters. The I/O line common with RXD line must be
defined as input mode (with or without pull-up)
while the I/O line common with TXD line must be
defined as output mode (Push-pull or open drain).
In the 11-bit character format option, the transmit-
ted data is inverted and can therefore use a single
transistor buffering stage. Defined as input, the
RXD line can be read at any time as an I/O line
during the UART operation. The TXD pin follows I/
O port registers value when UARTOE bit is
cleared, which means when no serial transmission
is in progress. As a consequence, a permanent
high level has to be written onto the I/O port in or-
der to achieve a proper stop condition on the TXD
line when no transmission is active.
Figure 30. UART Block Diagram
CONT
ROL
LOGI
C
T
O
CO
RE
START
DETECTOR
DATA SHIFT
REGISTER
D8 D7 D6 D5 D4 D3 D2 D1 D0
CONTROL REGISTER
BAUD RATE
RECEIVE BUFFER
REGISTER
PROGRAMMABLE
DIVIDER
DIN
DOUT
D8
BAUD RATE x 8
WRITE
READ
RXD1
TXD1
UARTOE
RX and TX
INTERRUPTS
TXD
DR
0
MUX
1
fOSC
VR02009
53
相關PDF資料
PDF描述
ST62P28CB3/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP28
ST6218CB6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20
ST62P18CB1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20
ST6327B1 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
ST6375B1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
相關代理商/技術參數
參數描述
ST62T18CM6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI/UAR RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T20CB3 功能描述:8位微控制器 -MCU ST6208C ST6209C ST6220C 8B MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T20CB6 功能描述:8位微控制器 -MCU OTP EPROM 4K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T20CB6 制造商:STMicroelectronics 功能描述:IC 8BIT MCU OTP 4K 62T20 DIP20
ST62T20CM6 功能描述:8位微控制器 -MCU OTP EPROM 4K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT