- 您現在的位置：買賣IC網 > PDF目錄299943 > ST52514F1 MAX II CPLD 570 LE 100-TQFP PDF資料下載
參數資料
| 型號： | ST52514F1 |
| 英文描述： | MAX II CPLD 570 LE 100-TQFP |
| 中文描述： | 8位重癥監護病房，10位ADC。兩個定時器/脈寬調制。 I2C總線。的SPI。脊髓損傷。提供了8K閃存 |
| 文件頁數： | 32/106頁 |
| 文件大?。?/td> | 1355K |
| 代理商： | ST52514F1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
31/106
Figure 4.1 Commands and Data Communication Sequences
The generic procedure of commands execution,
with the data communication in both directions is
displayed in Figure 4.1.
Remark: the Slave Address 1010000 must be sent
after a Stop (i.e. each time the data direction
changes, to specify the R/W bit). For example: if a
command to send data to the device has been
executed, a command for receiving data must be
followed by the slave address and the R/W bit must
be set to 1. The Programming Mode code doesn’t
need to be specified again.
Warning: After entering the Programming Mode,
the currently pointed address is the Page 48, Block
3, byte 0 (Lock Byte).
The
list
of
the
available
commands
in
Programming Mode is showed in Table 4.2
4.2.2 Fast Programming procedure. The
fastest way to program the device memory is the
use of the
FastBlockWrite command. The following
procedure can be used to write the memory with a
new program and new data, starting from the first
memory location:
1.
The Programming Mode is entered with the
sequence described above
2.
The memory is erased (all bits are put to 0)
with the
GlobalErase command. The device
holds the SCL line low, releasing it after the
command is completed (about 2 ms). This
command also unlocks the device if locked.
3.
The
FastBlockWrite command is sent and the
device acknowledges it
4.
The 32 bytes of data to be written in the first
memory Block are sent in a sequence. The
device acknowledges each of them
5.
After the device acknowledges the 32nd byte,
it holds the SCL line until the parallel writing of
the 32 byte is completed (about 2.5 ms)
6.
The Block Pointer is incremented by sending
the
IncBlock command
7.
The procedure is repeated from point 3 until
there is data to be sent to the memory
Note: the Block Pointer assumes values between
0 to 7 (there are 8 blocks in a page). When the
Block Pointer is equal to 7, the IncBlock command
puts this pointer to 0 and increments the Page
Pointer. The Page Pointer, after page writing is
completed, doesn’t have to be incremented in the
procedure above described.
4.2.3 Random data writing. A single byte can be
written in a specified memory location by using the
following procedure:
1.
The Programming Mode is entered with the
sequence described in Section 4.2.1
2.
The
SetPage command is sent, followed by
the page number where the data should be
written
3.
The
ByteWrite command is sent followed by
two bytes
4.
The first bytes that follows the ByteWrite com-
mand is the address inside the pointed page
where the data must be written.
5.
The second byte is the data to be written
6.
The device held the SCL line low until the data
is not stored in the memory (about 4.5 ms: 2
ms for erasing and 2.5 for writing)
Programming mode start sequence
Execution of commands for writing data:
Execution of commands for reading data:
S=Start, P=Stop, A=Acknowledge, NA=Non-acknowledge
From Slave to Master
From Master to Slave
S 10100000
A
00000000
A
Command
A
Data1
A
.....
DataN
AP
Command
A
Data1
A
.....
DataN
A
Command
A
Data1
A
.....
DataN
AP
Command
A
Address
A
P
S 10100001
A
Data read NA
P
相關PDF資料 |
PDF描述 |
|---|---|
| ST52514F3 | IC MAX 7000 CPLD 128 100-TQFP |
| ST52514G1 | IC MAX 7000 CPLD 32 44-TQFP |
| ST52514G3 | IC MAX 7000 CPLD 64 100-TQFP |
| ST52514K1 | IC MAX 7000 CPLD 128 100-FBGA |
| ST52514K3 | IC MAX 7000 CPLD 256 100-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST52514F3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH |
| ST52514G1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH |
| ST52514G3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH |
| ST52514K1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH |
| ST52514K3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT ICU WITH 10-BIT ADC. TWO TIMERS/PWM. I2C. SPI. SCI. UP TO 8K FLASH |
發布緊急采購，3分鐘左右您將得到回復。