- 您現在的位置：買賣IC網 > PDF目錄383838 > ST2L01K5R Stratix FPGA 80K BGA-956 PDF資料下載
參數資料
| 型號： | ST2L01K5R |
| 元件分類： | FPGA |
| 英文描述： | Stratix FPGA 80K BGA-956 |
| 中文描述： | 電壓調節器|固定/可調| 3.3 | 1.25 / 3.0V |園區| 5PIN |塑料 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 131K |
| 代理商： | ST2L01K5R |
ST2L01
5/12
APPLICATION HINTS
EXTERNAL CAPACITORS
Like any low-dropout regulator, the ST2L01
requires external capacitors for stability. We
suggest to solder both capacitors as close as
possible to the relative pins (1, 2 and 5).
INPUT CAPACITORS
An input capacitor, whose value is at least 1
μ
F, is
required; the amount of the input capacitance can
be increased without limit if a good quality
tantalum or aluminum capacitor is used.
SMS X7R or Y5V ceramic multilayer capacitors
could notensure stability in any condition because
of their variable characteristics with Frequency
and Temperature; the use of this capacitor is
strictly related to the use of the output capacitors.
For more details read the ”O(jiān)UTPUT CAPACITOR
SECTION”.
The input capacitor must be located at a distance
of not more than 0.5” from the input pin of the
device and returened to a clean analog ground.
OUTPUT CAPACITOR
The ST2L01 is designed specifically to work with
Ceramic and Tantalum capacitros.
Special care must be taken when a Ceramic
multilayer capacitor is used.
Special care must be taken when a Ceramic
multilayer capacitor is used.
Due to their characteristics they can sometimes
have an ESR value lower than the minimum
required by the ST2L01 and their relatively large
capacitance can change a lot with the ambient
temperature.
The test results of the ST2L01 stability using
multilayer
ceramic
capacitors
minimum value of 1
μ
F is needed for the adjustable
regulator (set to 2.5V). This value can be
increased up to 10
μ
F when a tantalum capacitor
is used on the input. A higher value C
O
can have
an ESR lower than the accepted minimum.
When a ceramic capacitor is used on the input the
output capacitance must be in the range from 1
μ
F
show
that
a
to 2.2
μ
F if C
I
=1
μ
F, and from 1
μ
F to 4.7
μ
F if
C
I
=2.2
μ
F.
The 3.3V regulator stable with a 470nF capacitor.
This value can be increased up to 10
μ
F if a
tantalum capacitor is used on the input. A higher
value C
O
can have an ESR lower than the
accepted minimum.
When a ceramic capacitor is used in the input the
output capacitance must bein the range from 1
μ
F
to 2.2
μ
F if C
I
=1
μ
F, and from 1
μ
F to 4.7
μ
F if
C
I
=2.2
μ
F.
Surface-mountable solid tantalum capacitors offer
a good combination of small physical size for the
capacitance value and ESR in the range needed
by the ST2L01. The test results show good
stability for both outputs with values of at least
1
μ
F. The value can be increased without limit for
even
better
performance
response and noise.
IMPORTANT
; The output capacitor must maintain
its ESR in the stable region over the full operating
temperature to assure stability. Also , capacitor
tolerance and variation with temperature must be
considered to assure that the minimum amount of
capacitance is provided at all times. For this
reason, when a ceramic multilayer capacitor is
used, the better choise for temperature coefficent
is the X7R type, which holds the capacitance
within
±
15% . The output capacitor should be
located not more than 0.5” from theoutput pins of
the device and returned to a clean analog ground.
such
a
transient
ADJUSTABLE REGULATOR
The ST2L01 has a 1.25V reference voltage
between the output and the adjustable pins
(respectevely pin 4 and 2). When a resistor R2 is
placed between these two therminals a constant
current flows through R2 and down to R1 to set
the overall (V
O2
to GND) output voltage.
Minimum load current is 1mA.
I
ADJ
is very small (typically 35
μ
A) and constant; in
the V
O
calculation it can be ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| ST2L01PTR | Stratix FPGA 80K FBGA-1020 |
| ST3243EB | Stratix FPGA 30K FBGA-1020 |
| ST3243EC | Stratix FPGA 30K FBGA-1020 |
| ST3384B | Stratix GX FPGA 25K 4-FBGA |
| ST3384C | Stratix GX FPGA 25K 4-FBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST2L01PT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DUAL VOLTAGE REGULATOR |
| ST2L01PTR | 功能描述:IC REG LDO 3.3V/ADJ 1A 5-PPAK RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.1V 輸入電壓:最高 5.5V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:300mA 電流 - 限制（最小）:420mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 供應商設備封裝:TSOT-23-5 包裝:帶卷 (TR) |
| ST2L05 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:VERY LOW QUIESCENT CURRENT DUAL VOLTAGE REGULATOR |
| ST2L05-1500 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:VERY LOW QUIESCENT CURRENT DUAL VOLTAGE REGULATOR |
| ST2L05-1500PT | 功能描述:低壓差穩壓器 - LDO 1.5V Fix/Adj 1.0 Amp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。