- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C580IP40 (EXAR CORP) UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER PDF資料下載
參數資料
| 型號： | ST16C580IP40 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| 中文描述： | 1 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PDIP40 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-40 |
| 文件頁數： | 6/41頁 |
| 文件大小： | 244K |
| 代理商： | ST16C580IP40 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
ST16C580
6
Rev. 1.20
RESET
35
39
35
I
Reset. (active high) - A logic 1 on this pin will reset the internal
registers and all the outputs. The UART transmitter output
and the receiver input will be disabled during reset time. (See
ST16C580 External Reset Conditions for initialization de-
tails.)
VCC
40
44
42
Pwr
Power Supply Input.
XTAL1
16
18
14
I
Crystal or External Clock Input - Functions as a crystal input
or as an external clock input. A crystal can be connected
between this pin and XTAL2 to form an internal oscillator
circuit. An external 1 M
resistor is required between the
XTAL1 and XTAL2 pins (see figure 9). Alternatively, an
external clock can be connected to this pin to provide
custom data rates (Programming Baud Rate Generator
section).
XTAL2
17
19
15
O
Output of the Crystal Oscillator or Buffered Clock - (See also
XTAL1). Crystal oscillator output or buffered clock output.
-CD
38
42
40
I
Carrier Detect (active low) - A logic 0 on this pin indicates
that a carrier has been detected by the modem.
-CTS
36
40
38
I
Clear to Send (active low) - A logic 0 on the -CTS pin
indicates the modem or data set is ready to accept transmit
data from the 580. Status can be tested by reading MSR bit-
4. This pin only affects the transmit and receive operations
when Auto CTS function is enabled via the Enhanced
Feature Register (EFR) bit-7, for hardware flow control
operation.
-DSR
37
41
39
I
Data Set Ready (active low) - A logic 0 on this pin indicates
the modem or data set is powered-on and is ready for data
exchange with the UART. This pin has no effect on the
UART’s transmit or receive operation.
-DTR
33
37
33
O
Data Terminal Ready (active low) - A logic 0 on this pin
indicates that the 580 is powered-on and ready. This pin can
be controlled via the modem control register. Writing a logic
1 to MCR bit-0 will set the -DTR output to logic 0, enabling
the modem. This pin will be a logic 1 after writing a logic 0
to MCR bit-0, or after a reset. This pin has no effect on the
SYMBOL DESCRIPTION
Symbol
Pin
44
Signal
type
Pin Description
40
48
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C580IQ48 | UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580CP40 | Linear Voltage Regulator IC; Output Current Max:350mA; Supply Voltage Max:6V; Package/Case:8-TSSOP; Output Current:350mA; Output Voltage:3.3V; Current Rating:30.05A; Leaded Process Compatible:No; Output Voltage Max:3.3V |
| ST16C580CJ44 | UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C654CJ68 | 2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO |
| ST16C654CQ100 | 2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C580IQ48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580IQ48-F | 功能描述:UART 接口集成電路 UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C650 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650A | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650A_0508 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。