參數資料
型號： ST16C554DCJ68
廠商： STARTECH SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： QUAD UART WITH 16-BYTE FIFOS
中文描述： 4 CHANNEL(S), 448K bps, SERIAL COMM CONTROLLER, PQCC68
文件頁數： 22/40頁
文件大?。?/td> 518K
代理商： ST16C554DCJ68
ST16C554/554D/68C554
22
Rev. 3.10
LCR
Bit-5
LCR
Bit-4
LCR
Bit-3
Parity selection
X
0
0
1
1
X
0
1
0
1
0
1
1
1
1
No parity
Odd parity
Even parity
Force parity 1
Forced parity 0
LCR BIT-6:
When enabled the Break control bit causes a break
condition to be transmitted (the TX output is forced to
a logic 0 state). This condition exists until disabled by
setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (normal default
condition)
Logic 1 = Forces the transmitter output (TX) to a logic
0 for alerting the remote receiver to a line break
condition.
LCR BIT-7:
Not used - Initialized to a logic 0.
Modem Control Register (MCR)
This register controls the interface with the modem or
a peripheral device.
MCR BIT-0:
Logic 0 = Force -DTR output to a logic 1. (normal
default condition)
Logic 1 = Force -DTR output to a logic 0.
MCR BIT-1:
Logic 0 = Force -RTS output to a logic 1. (normal
default condition)
Logic 1 = Force -RTS output to a logic 0.
MCR BIT-2:
This bit is used in the Loopback mode only. In the
loopback mode this bit is use to write the state of the
modem -RI interface signal via -OP1.
MCR BIT-3: (
Used to control the modem -CD signal
in the loopback mode.)
Logic 0 = Forces INT (A-D) outputs to the three state
mode during the 16 mode. (normal default condition)
In the Loopback mode, sets -OP2 (-CD) internally to a
logic 1.
Logic 1 = Forces the INT (A-D) outputs to the active
mode during the 16 mode. In the Loopback mode, sets
-OP2 (-CD) internally to a logic 0.
MCR BIT-4:
Logic 0 = Disable loopback mode. (normal default
condition)
Logic 1 = Enable local loopback mode (diagnostics).
MCR BIT 5-7:
Not used - Initialized to a logic 0.
Line Status Register (LSR)
This register provides the status of data transfers
between. the 554D and the CPU.
LSR BIT-0:
Logic 0 = No data in receive holding register or FIFO.
(normal default condition)
Logic 1 = Data has been received and is saved in the
receive holding register or FIFO.
LSR BIT-1:
Logic 0 = No overrun error. (normal default condition)
Logic 1 = Overrun error. A data overrun error occurred
in the receive shift register. This happens when addi-
tional data arrives while the FIFO is full. In this case
the previous data in the shift register is overwritten.
Note that under this condition the data byte in the
receive shift register is not transfered into the FIFO,
therefore the data in the FIFO is not corrupted by the
error.
LSR BIT-2:
Logic 0 = No parity error. (normal default condition)
Logic 1 = Parity error. The receive character does not
have correct parity information and is suspect. In the
FIFO mode, this error is associated with the character
at the top of the FIFO.
LSR BIT-3:
Logic 0 = No framing error. (normal default condition)
Logic 1 = Framing error. The receive character did not
相關PDF資料
PDF描述
ST68C554 QUAD UART WITH 16-BYTE FIFOS
ST16C554DIJ68 Plug-In Relay; Contacts:DPDT; Contact Carry Current:15A; Coil Voltage AC Max:120V; Relay Mounting:Plug-In; Relay Terminals:Quick Connect; Coil Resistance:4430ohm RoHS Compliant: Yes
ST16C554DIQ64 QUAD UART WITH 16-BYTE FIFOS
ST16C554CQ64 Linear Voltage Regulator IC; Output Current Max:350mA; Supply Voltage Max:6V; Package/Case:8-TSSOP; Current Rating:350mA; Leaded Process Compatible:No; Output Voltage Max:2.8V; Peak Reflow Compatible (260 C):No
ST16C554DCQ64 QUAD UART WITH 16-BYTE FIFOS
相關代理商/技術參數
參數描述
ST16C554DCJ-68 制造商:Exar Corporation 功能描述:IC,UART,LDCC,68PIN,PLASTIC
ST16C554DCJ68-F 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C554DCJ68TR 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C554DCJ68TR-F 功能描述:UART 接口集成電路 QUAD UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C554DCQ-0A-EB 功能描述:界面開發工具 Supports C554D 64 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*