參數資料
型號： ST16C552
廠商： Exar Corporation
英文描述： Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）)
中文描述： 雙UART），16字節FIFO和并行打印機端口（雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）
文件頁數： 4/40頁
文件大?。?/td> 463K
代理商： ST16C552
4
ST16C552/552A
Rev. 3.30
SYMBOL DESCRIPTION
Symbol
Pin
Signal Type
Pin Description
-ERROR
63
I
Error, Printer (with internal pull-up) - General purpose input
or line printer error. This pin may be connected to the active
low (logic 0) output of a printer to indicate an error condition.
GND
2,7,54
27
Pwr
Signal and Power Ground.
INIT
57
I/O
Initialize (open drain, with internal pull-up) - General pur-
pose I/O signal. This pin may be connected for initialization
service of a connected line printer. Generally when this
signal is a logic 0, any connected printer will be initialized.
INT A/B
45,60
O
Interrupt output A/B ( three state active high) - These pins
provide individual channel interrupts, INT A-B. INT A-B are
enabled when MCR bit-3 is set to a logic 1, interrupts are
enabled in the interrupt enable register (IER), and when an
interrupt condition exists. Interrupt conditions include: re-
ceiver errors, available receiver buffer data, transmit buffer
empty, or when a modem status flag is detected.
-INTP
59
O
Printer Interrupt, - This pin can be used to signal the
interrupt status of a connected printer. This pin basically
tracks the -ACK input pin, When INTSEL is a logic 0 and
interrupts are enabled by bit-4 in the control register. A
latched mode can be selected by setting INTSEL to a logic
1. In this case the interrupt -INTP is generated normally but
does not return to the inactive state until the trailing edge of
the read cycle (-IOR pin). -INTP is three stated until CON
bit-4 is set to a logic 1. The difference between the
ST16C552 and ST16C552A is the output state of INTP.
INTP is active high (logic 1) on the ST16C552 whereas
INTP is active low (logic 0) on the ST16C552A part when the
interrupt latch mode is selected.
INTSEL
43
I
Interrupt Select mode - This pin selects the interrupt type for
the printer port (-INTP). When this pin is a logic 0, the
external -ACK signal state is generally followed, minus
some minor propagation delay. Making this pin a logic 1 or
connecting it to VCC will set the interrupt latched mode. In
this case the printer interrupt (-INTP) will not return to a logic
0 on the 552 or a logic 1 on the 552A (552A is inverted), until
the trailing edge of -IOR (end of the external CPU read
相關PDF資料
PDF描述
ST16C552A Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）)
ST16C554DCJ68 QUAD UART WITH 16-BYTE FIFOS
ST68C554 QUAD UART WITH 16-BYTE FIFOS
ST16C554DIJ68 Plug-In Relay; Contacts:DPDT; Contact Carry Current:15A; Coil Voltage AC Max:120V; Relay Mounting:Plug-In; Relay Terminals:Quick Connect; Coil Resistance:4430ohm RoHS Compliant: Yes
ST16C554DIQ64 QUAD UART WITH 16-BYTE FIFOS
相關代理商/技術參數
參數描述
ST16C552ACJ68 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C552ACJ68-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C552ACJ68TR-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C552AIJ68 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT
ST16C552AIJ68-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*