- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C452CJ68 (EXAR CORP) Power Supply IC; Number of Outputs:1; Supply Voltage Max:5.5V; Package/Case:10-MSOP; Leaded Process Compatible:No; Output Current:150mA; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Power Dissipation:481mW PDF資料下載
參數資料
| 型號： | ST16C452CJ68 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Power Supply IC; Number of Outputs:1; Supply Voltage Max:5.5V; Package/Case:10-MSOP; Leaded Process Compatible:No; Output Current:150mA; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Power Dissipation:481mW |
| 中文描述： | 2 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 封裝： | PLASTIC, LCC-68 |
| 文件頁數： | 8/30頁 |
| 文件大?。?/td> | 162K |
| 代理商： | ST16C452CJ68 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
8
ST16C452/452PS
Rev. 3.20
GENERAL DESCRIPTION
The 452/452PS provides serial asynchronous receive
data synchronization, parallel-to-serial and serial-to-
parallel data conversions for both the transmitter and
receiver sections. These functions are necessary for
converting the serial data stream into parallel data that
is required with digital data systems. Synchronization
for the serial data stream is accomplished by adding
start and stops bits to the transmit data to form a data
character (character orientated protocol). Data integ-
rity is insured by attaching a parity bit to the data
character. The parity bit is checked by the receiver for
any transmission bit errors. The electronic circuitry to
provide all these functions is fairly complex especially
when manufactured on a single integrated silicon
chip. The 452/452PS represents such an integration
with greatly enhanced features. The 452/452PS is
fabricated with an advanced CMOS process.
The 452/452PS combines the package functions of a
dual UART and a printer interface on a single inte-
grated chip. The 452/452PS UART is indented to be
software compatible with the ST16C450, and
NS16C450 while the bi-directional printer interface
mode is intended to operate with a CENTRONICS
type parallel printer. However, the printer interface is
designed such that it may be configured to operate
with other parallel printer interfaces or used as a
general purpose parallel interface. The 452 is avail-
able in two versions, the ST16C452 and the
ST16C452PS. The ST16C452 provides single hard-
ware pin to control the printer port data direction while
the 452PS provides an additionally software control
bit to control the printer port data direction to become
compatible PS/2 operating system.
The 452/452PS is capable of operation to 1.5Mbps
with a 24 MHz external clock input. With an external
clock input of 1.8432 MHz the user can select data
rates up to 115.2 Kbps.
FUNCTIONAL DESCRIPTIONS
Functional Modes
Two functional user modes are selectable for the 452/
452PS package. The first of these provides the dual
UART functions, while the other provides the func-
tions of a parallel printer interface. These features are
available through selection at the package interface
select pins.
UART A-B Functions
The UART mode provides the user with the capability
to transfer information between an external CPU and
the 452/452PS package. A logic 0 on chip select pins
-CSA or -CSB allows the user to configure, send data,
and/or receive data via the UART channels A-B.
Printer Port Functions
The Printer mode provides the user with the capability
to transfer information between an external CPU and
the 452/452PS parallel printer port. A logic 0 on chip
select pin -CSP allows the user to configure, send
data, and/or receive data via the bi-directional parallel
8-bit data bus, PD0-PD7.
Internal Registers
The 452/452PS provides 11 internal registers for
monitoring and control of the UART functions and
another 6 registers for monitoring and controlling the
printer port. These resisters are shown in Table 4
below. The UART registers function as data holding
registers (THR/RHR), interrupt status and control
registers (IER/ISR), line status and control registers
(LCR/LSR), modem status and control registers
(MCR/MSR), programmable data rate (clock) control
registers (DLL/DLM), and a user assessable
scratchpad register (SPR). The printer port registers
functions data holding registers (PR), I/O status regis-
ter (SR), I/O select register (IOSEL), and a command
and control register (COM/CON). Register functions
are more fully described in the following paragraphs.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C452CJ68PS | Power Supply IC; Number of Outputs:1; Supply Voltage Max:5.5V; Package/Case:10-MSOP; Leaded Process Compatible:No; Output Current:150mA; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Power Dissipation:481mW |
| ST16C452PS | Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) |
| ST16C452 | Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) |
| ST16C550 | UART with 16-Byte FIFO(通用異步接收器/發送器（帶16字節的先進先出）) |
| ST16C552 | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C452CJ68-F | 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C452CJ68PS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C452CJ68PS-F | 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C452CJ68TR-F | 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C452IJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。