- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C452 (Exar Corporation) Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) PDF資料下載
參數資料
| 型號： | ST16C452 |
| 廠商： | Exar Corporation |
| 英文描述： | Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) |
| 中文描述： | 雙UART與并行打印機端口（雙通用異步接收器/發送器（帶并行打印機端口）） |
| 文件頁數： | 20/30頁 |
| 文件大小： | 389K |
| 代理商： | ST16C452 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
20
ST16C452/452PS
Rev. 3.10
a logic 1 first.
Logic 0 = -AutoFDXT pin is a logic 1. (normal default
condition)
1= -AutoFDXT pin is a logic 0.
COM BIT-2:
INIT is a bi-directional signal with an open source
driver and internal pull-up so that it may be wire-ord
with other outputs. COM bit-2 is used to read status
while CON bit 2 is used to set an output state. If it is to
function as an input, CON bit-1 shall be set to a logic
1 first.
Logic 0 = INIT pin is a logic 0. (normal default
condition)
Logic 1 = INIT pin is a logic 1.
COM BIT-3:
-SLCTIN is a bi-directional signal with an open source
driver and internal pull-up so that it may be wire-ord
with other outputs. COM bit-1 is used to read status
while CON bit 1 is used to set an output state. If it is to
function as an input, CON bit-1 shall be set to a logic
1 first.
Logic 0 = -SLCTIN pin is a logic 1 (normal default
condition)
Logic 1 = -SLCTIN pin is a logic 0
COM BIT-4:
This bit allows the state of -INTP to be read back by the
external CPU.
Logic 0 = Interrupt (-INTP output) is disabled (normal
default condition)
Logic 1 = Interrupt (-INTP output) is enabled
COM BIT 5-7:
Not Used - initialized to a logic 1.
Control Register (CON)
This register provides control of the printer port output
logical states and controls the printer interrupts INIT
and -INTP. With the exception of PD 0-7 IN/OUT, the
status of this register may be read by reading the COM
register.
CON BIT-0:
The -STROBE output control bit is under software
control, i.e., the hardware will not generate a strobe. It
is up to software to return the state of -STROBE to the
inactive (logic 1) state. The hardware driver is open
drain so that -STROBE may be wire-ord. The state of
this bit can be read using COM bit-0.
Logic 0 = -STROBE output is set to a logic 1. (normal
default condition)
Logic 1 = -STROBE output is set to a logic 0.
CON BIT-1:
The -AutoFDXT output control bit is set by software
using CON bit-1. The hardware driver is open drain so
that -AutoFDXT may be wire-ord. The state of this bit
can be read using COM bit-1.
Logic 0 = -AutoFDXT output is set to a logic 1. (normal
default condition)
Logic 1 = -AutoFDXT output is set to a logic 0.
CON BIT-2:
The INIT output control bit is set by software using
CON bit-2. The hardware driver is open drain so that
INIT may be wire-ord. The state of this bit can be read
using COM bit-2.
Logic 0 = INIT output is set to a logic 0. (normal default
condition)
Logic 1 = INIT output is set to a logic 1.
CON BIT-3:
The -SLCTIN output control bit is set by software using
CON bit-3. The hardware driver is open drain so that
-AutoFDXT may be wire-ord. The state of this bit can
be read using COM bit-3.
Logic 0 = -SLCTIN output is set to a logic 1. (normal
default condition)
Logic 1 = -SLCTIN output is set to a logic 0.
CON BIT-4:
This bit enables or masks the printer interrupt output
-INTP. The state of this bit can be read using COM bit-
4.
Logic 0 = Disable -INTP output. (normal default con-
dition)
Logic 1 = Enable -INTP output.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C550 | UART with 16-Byte FIFO(通用異步接收器/發送器（帶16字節的先進先出）) |
| ST16C552 | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C552A | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C554DCJ68 | QUAD UART WITH 16-BYTE FIFOS |
| ST68C554 | QUAD UART WITH 16-BYTE FIFOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C452CJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:UART 2-CH 3.3V/5V 68-Pin PLCC |
| ST16C452CJ68-F | 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C452CJ68PS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C452CJ68PS-F | 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C452CJ68TR-F | 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。