- 您現在的位置：買賣IC網 > PDF目錄383836 > ST16C1550CJ28 (EXAR CORP) 2.97V TO 5.5V UART WITH 16-BYTE FIFO PDF資料下載
參數資料
| 型號： | ST16C1550CJ28 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| 中文描述： | 1 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC28 |
| 封裝： | PLASTIC, LCC-28 |
| 文件頁數： | 19/37頁 |
| 文件大?。?/td> | 428K |
| 代理商： | ST16C1550CJ28 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
á
REV. 4.2.0
ST16C1550/51
2.97V TO 5.5V UART WITH 16-BYTE FIFO
19
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Transmit FIFO Trigger Select
These 2 bits are only active when IER bit-5 is a ‘1’.
(logic 0 = default, TX trigger level = 1)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load.
Table 6
shows the selections.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level.
Table 6
shows the complete selections.
4.6
The Line Control Register is used to specify the asynchronous data communication format. The word or
character length, the number of stop bits, and the parity are selected by writing the appropriate bits in this
register.
LCR[1:0]: TX and RX Word Length Select
These two bits specify the word length to be transmitted or received.
Line Control Register (LCR) - Read/Write
T
ABLE
6: T
RANSMIT
AND
R
ECEIVE
FIFO T
RIGGER
L
EVEL
S
ELECTION
FCR
B
IT
-7
FCR
B
IT
-6
FCR
B
IT
-5
FCR
BIT
-4
R
ECEIVE
T
RIGGER
L
EVEL
T
RANSMIT
T
RIGGER
L
EVEL
0
0
1
1
0
1
0
1
1
4
8
14
0
0
1
1
0
1
0
1
1
4
8
14
BIT-1
BIT-0
W
ORD
LENGTH
0
0
5 (default)
0
1
6
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C1550CP28 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550CQ48 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550IJ28 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550IP28 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550IQ48 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C1550CJ28-F | 功能描述:UART 接口集成電路 UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C1550CJ28-F | 制造商:Exar Corporation 功能描述:IC SGL UART 1.5MBPS 5.5V 28-PLCC |
| ST16C1550CJ28TR-F | 功能描述:UART 接口集成電路 UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C1550CP28 | 制造商:Exar Corporation 功能描述: |
| ST16C1550CQ48 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。