- 您現在的位置：買賣IC網 > PDF目錄383836 > ST16C1451IQ48 (EXAR CORP) 2.97V TO 5.5V UART PDF資料下載
參數資料
| 型號： | ST16C1451IQ48 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2.97V TO 5.5V UART |
| 中文描述： | 1 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 1 MM HEIGHT, TQFP-48 |
| 文件頁數： | 19/32頁 |
| 文件大?。?/td> | 355K |
| 代理商： | ST16C1451IQ48 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
á
REV. 4.2.0
ST16C1450/51
2.97V TO 5.5V UART
19
MCR[2]: OP1# Output/Soft Reset
OP1# is not available as an output pin on the 145X. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
Logic 0 = OP1# output (RI# input) is at logic 1 (default).
Logic 1 = OP1# output (RI# input) is at logic 0.
In normal operation, this bit is associated with the RST (buffered reset) output pin. The logical state of the RST
pin will follow exactly the logical state of the RESET pin. When IER bit-5 = 1, soft resets from MCR bit-2 are
ORed with the state of the RESET input pin. Therefore both reset types will be seen at the RST pin. Note that
asserting MCR bit-2 does not reset the 145X.
Logic 0 = The RST output pin is a logic 0 (default).
Logic 1 = The RST output pin is a logic 1.
MCR[3]: OP2# or INT Output Enable
When not in Internal Loopback Mode:
Logic 0 = INT output is three-state (default).
Logic 1 = INT output is active high.
OP2# is not available as an output pin on the 145X. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem CD# interface signal.
Logic 0 = OP2# output (CD# input) is a logic 1 (default).
Logic 1 = OP2# output (CD# input) is a logic 0.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and
Figure 7
.
MCR[6:5]: Reserved
MCR[7]: Power Down Enable
This bit can only be accessed when IER bit-5 = 1.
Logic 0 = Normal mode (default).
Logic 1 = Power down mode.
See “Power Down Mode” on page 11.
4.7
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host. If IER bit-2 is set to a logic
1, an LSR interrupt will be generated when the character that is in the RHR has an error (parity, framing,
overrun, break).
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register (default).
Logic 1 = Data has been received and is saved in the receive holding register.
LSR[1]: Receiver Overrun Error Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while there is data in the RHR. In this case the previous data in the receive shift
register is overwritten. Note that under this condition the data byte in the receive shift register is not
transferred into the RHR, therefore the data in the RHR is not corrupted by the error.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C1451 | 2.97V TO 5.5V UART |
| ST16C1550 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550CJ28 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550CP28 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550CQ48 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C1550 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550CJ28 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C1550CJ28-F | 功能描述:UART 接口集成電路 UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C1550CJ28-F | 制造商:Exar Corporation 功能描述:IC SGL UART 1.5MBPS 5.5V 28-PLCC |
發布緊急采購，3分鐘左右您將得到回復。