- 您現在的位置：買賣IC網 > PDF目錄383836 > ST16C1451 (Exar Corporation) 2.97V TO 5.5V UART PDF資料下載
參數資料
| 型號： | ST16C1451 |
| 廠商： | Exar Corporation |
| 英文描述： | 2.97V TO 5.5V UART |
| 中文描述： | 2.97V至5.5V的UART |
| 文件頁數： | 6/32頁 |
| 文件大?。?/td> | 355K |
| 代理商： | ST16C1451 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ST16C1450/51
2.97V TO 5.5V UART
á
REV. 4.2.0
6
RTS#
22
22
22
22
31
O
Request to Send or general purpose output (active low). If
this pin is not needed for modem communication, then it can
be used as a general I/O. If it is not used, leave it uncon-
nected.
CTS#
25
25
25
25
34
I
Clear to Send or general purpose input (active low). If this
pin is not needed for modem communication, then it can be
used as a general I/O. If it is not used, connect it to VCC.
DTR#
23
23
23
23
32
O
Data Terminal Ready or general purpose output (active
low). If this pin is not needed for modem communication,
then it can be used as a general I/O. If it is not used, leave it
unconnected.
DSR#
26
26
26
26
39
I
Data Set Ready input or general purpose input (active low).
If this pin is not needed for modem communication, then it
can be used as a general I/O. If it is not used, connect it to
VCC.
CD#
27
27
27
27
40
I
Carrier Detect input or general purpose input (active low). If
this pin is not needed for modem communication, then it can
be used as a general I/O. If it is not used, connect it to VCC.
RI#
17
16
17
16
21
I
Ring Indicator input or general purpose input (active low). If
this pin is not needed for modem communication, then it can
be used as a general I/O. If it is not used, connect it to VCC.
ANCILLARY SIGNALS
CLK
-
12
-
12
-
I
External Clock Input. This function is associated with 28 pin
PDIP and 28 pin PLCC ST16C1451 packages only. An
external clock must be connected to this pin to clock the
baud rate generator and internal circuitry.
XTAL1
12
-
12
-
15
I
Crystal or external clock input. See
Figure 4
for typical
oscillator connections.
XTAL2
13
-
13
-
16
O
Crystal or buffered clock output. See
Figure 4
for typical
oscillator connections.
RESET
24
24
24
24
33
I
Reset Input (active high). When it is asserted, the UART
configuration registers are reset to default values, see
Table 6
.
RST
-
17
-
17
22
O
Reset Output (active high). This output is only available on
the ST16C1451. When IER bit-5 is a logic 0, RST will follow
the logical state of the RESET pin. When IER bit-5 is a logic
1, the user may send software (soft) resets via MCR bit-2.
Soft resets from MCR bit-2 are “ORed” with the state of the
RESET pin.
VCC
28
28
28
28
41
Pwr
Power supply input of 2.97 to 5.5V.
N
AME
28-P
IN
PDIP
(1450)
28-P
IN
PDIP
(1451)
28-P
IN
PLCC
(1450)
28-P
IN
PLCC
(1451)
48-P
IN
TQFP
(145X)
T
YPE
D
ESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C1550 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550CJ28 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550CP28 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550CQ48 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
| ST16C1550IJ28 | 2.97V TO 5.5V UART WITH 16-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C1451CJ28 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
| ST16C1451CP28 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
| ST16C1451CQ48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
| ST16C1451IJ28 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
| ST16C1451IP28 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
發布緊急采購，3分鐘左右您將得到回復。