- 您現在的位置：買賣IC網 > PDF目錄10404 > SSM2335CBZ-REEL (Analog Devices Inc)IC AMP AUDIO 4.28W MONO D 9WLCSP PDF資料下載
參數資料
| 型號： | SSM2335CBZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/16頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO 4.28W MONO D 9WLCSP |
| 產品變化通告： | 8mm Carrier Tape Changes 28/Feb/2012 |
| 標準包裝： | 10,000 |
| 類型： | D 類 |
| 輸出類型： | 1-通道（單聲道） |
| 在某負載時最大輸出功率 x 通道數量： | 4.28W x 1 @ 3 歐姆 |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，短路和熱保護，關閉 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 9-WLCSP（1.52 x 1.69） |
| 封裝/外殼： | 9-UFBGA，WLCSP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
SSM2335
Rev. 0 | Page 12 of 1
6
OUTPUT > 0V
+5V
0V
THEORY OF OPERATION
OVERVIEW
The SSM2335 mono Class-D audio amplifier features a filterless
modulation scheme that greatly reduces the external component
count, conserving board space and, thus, reducing systems cost.
The SSM2335 does not require an output filter but, instead, relies
on the inherent inductance of the speaker coil and the natural
filtering of the speaker and human ear to fully recover the audio
component of the square wave output. Most Class-D amplifiers
use some variation of pulse-width modulation (PWM), but the
SSM2335 uses Σ-Δ modulation to determine the switching
pattern of the output devices, resulting in a number of important
benefits. Σ-Δ modulators do not produce a sharp peak with many
harmonics in the AM frequency band, as pulse-width modulators
often do. Σ-Δ modulation provides the benefits of reducing the
amplitude of spectral components at high frequencies, that is,
reducing EMI emission that might otherwise be radiated by
speakers and long cable traces. The SSM2335 does not require
external EMI filtering for twisted speaker cable lengths shorter
than 10 cm. Due to the inherent spread-spectrum nature of Σ-Δ
modulation, the need for oscillator synchronization is eliminated
for designs incorporating multiple SSM2335 amplifiers.
The SSM2335 also offers protection circuits for overcurrent and
temperature protection.
GAIN
The SSM2335 has a default gain of 18 dB that can be reduced by
using a pair of external resistors with a value calculated as follows:
External Gain Settings = 160 kΩ/(20 kΩ + REXT)
POP-AND-CLICK SUPPRESSION
Voltage transients at the output of audio amplifiers can occur
when shutdown is activated or deactivated. Voltage transients
as low as 10 mV can be heard as an audio pop in the speaker.
Clicks and pops can also be classified as undesirable audible
transients generated by the amplifier system and, therefore, as
not coming from the system input signal. Such transients may
be generated when the amplifier system changes its operating
mode. For example, the following may be sources of audible
transients: system power-up and power-down, mute and unmute,
input source change, and sample rate change. The SSM2335 has
a pop-and-click suppression architecture that reduces these out-
put transients, resulting in noiseless activation and deactivation.
OUTPUT MODULATION DESCRIPTION
The SSM2335 uses three-level, Σ-Δ output modulation. Each
output can swing from GND to VDD and vice versa. Ideally, when
no input signal is present, the output differential voltage is 0 V
because there is no need to generate a pulse. In a real-world
situation, there are always noise sources present.
Due to this constant presence of noise, a differential pulse is
generated, when required, in response to this stimulus. A small
amount of current flows into the inductive load when the differ-
ential pulse is generated.
Most of the time, however, output differential voltage is 0 V, due
to the Analog Devices patent pending, three-level, Σ-Δ output
modulation. This feature ensures that the current flowing through
the inductive load is small.
When the user wants to send an input signal, an output pulse is
generated to follow the input voltage. The differential pulse
density is increased by raising the input signal level. Figure 33
depicts three-level, Σ-Δ output modulation with and without
input stimulus.
OUT+
+5V
0V
OUT–
+5V
0V
VOUT
OUTPUT < 0V
+5V
0V
OUT+
+5V
0V
OUT–
0V
–5V
VOUT
OUTPUT = 0V
OUT+
+5V
0V
+5V
0V
OUT–
+5V
–5V
0V
VOUT
07
55
1-
0
33
Figure 33. Three-Level, Σ-Δ Output Modulation With and Without Input Stimulus
相關PDF資料 |
PDF描述 |
|---|---|
| VE-260-IW-F1 | CONVERTER MOD DC/DC 5V 100W |
| VI-JWK-MY-B1 | CONVERTER MOD DC/DC 40V 50W |
| VI-2WK-IW-F4 | CONVERTER MOD DC/DC 40V 100W |
| VI-2WK-IW-F1 | CONVERTER MOD DC/DC 40V 100W |
| VI-JWH-MY-B1 | CONVERTER MOD DC/DC 52V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SSM2335CBZ-REEL7 | 功能描述:IC AMP AUDIO 4.28W MONO D 9WLCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 標準包裝:2,000 系列:- 類型:AB 類 輸出類型:2 通道（立體聲） 在某負載時最大輸出功率 x 通道數量:- 電源電壓:4 V ~ 18 V 特點:- 安裝類型:通孔 供應商設備封裝:8-DIP 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 |
| SSM2356 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2 × 2W Filterless Class-D Stereo Audio Amplifier |
| SSM2356CBZ-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:2 × 2W Filterless Class-D Stereo Audio Amplifier |
| SSM2356CBZ-REEL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2 × 2W Filterless Class-D Stereo Audio Amplifier |
| SSM2356CBZ-RL | 功能描述:IC AMP AUD 2X2W STER D 16WLCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道（單聲道），帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音，差分輸入，I²C，靜音，關閉，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND |
發布緊急采購，3分鐘左右您將得到回復。