- 您現在的位置：買賣IC網 > PDF目錄385860 > SSM2211SZ-REEL1 (Analog Devices, Inc.) Low Distortion, 1.5 W Audio Power Amplifier PDF資料下載
參數資料
| 型號： | SSM2211SZ-REEL1 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low Distortion, 1.5 W Audio Power Amplifier |
| 中文描述： | 低失真，1.5 W音頻功率放大器 |
| 文件頁數： | 15/24頁 |
| 文件大?。?/td> | 408K |
| 代理商： | SSM2211SZ-REEL1 |
SSM2211
TYPICAL APPLICATIONS
Rev. D | Page 15 of 24
SSM2211
AUDIO
INPUT
SPEAKER
8V
R
F
C
S
5V
2
7
1
8
5
6
4
3
–
+
C
C
R
I
C
B
–
+
0
Figure 42. Typical Configuration
Figure 42 shows how the SSM2211 is connected in a typical
application. The SSM2211 can be configured for gain much like
a standard operational amplifier. The gain from the audio input
to the speaker is
I
F
V
R
R
A
×
=
2
(1)
The 2× factor comes from the fact that Pin 8 has the opposite
polarity of Pin 5, providing twice the voltage swing to the
speaker from the bridged-output configuration.
C
S
is a supply bypass capacitor used to provide power supply
filtering. Pin 2 is connected to Pin 3 to provide an offset voltage
for single-supply use, with C
B
providing a low ac impedance to
ground to help power supply rejection. Because Pin 4 is a
virtual ac ground, the input impedance is equal to R
I
. C
C
is the
input coupling capacitor, which also creates a high-pass filter
with a corner frequency of
1
C
I
HP
C
R
f
×
π
=
2
(2)
Because the SSM2211 has an excellent phase margin, a feedback
capacitor in parallel with R
F
to band limit the amplifier is not
required, as it is in some competitor products.
BRIDGED OUTPUT VS. SINGLE-ENDED OUTPUT
CONFIGURATIONS
The power delivered to a load with a sinusoidal signal can be
expressed in terms of the peak voltage of the signal and the
resistance of the load as
L
PK
×
L
R
V
P
=
2
2
(3)
By driving a load from a bridged-output configuration, the
voltage swing across the load doubles. Therefore, an advantage
in using a bridged-output configuration becomes apparent from
Equation 3, as doubling the peak voltage results in four times
the power delivered to the load. In a typical application
operating from a 5 V supply, the maximum power that can be
delivered by the SSM2211 to an 8 Ω speaker in a single-ended
configuration is 250 mW. By driving this speaker with a bridged
output, 1 W of power can be delivered. This translates to a
12 dB increase in sound pressure level from the speaker.
Driving a speaker differentially from a bridged output offers
another advantage in that it eliminates the need for an output
coupling capacitor to the load. In a single-supply application,
the quiescent voltage at the output is half of the supply voltage.
If a speaker is connected in a single-ended configuration, a
coupling capacitor is needed to prevent dc current from flowing
through the speaker. This capacitor also needs to be large
enough to prevent low frequency roll-off. The corner frequency
is given by
1
dB
3
C
L
C
R
f
×
=
π
2
(4)
where
R
L
is the speaker resistance and
C
C
is the coupling
capacitance.
For an 8 Ω speaker and a corner frequency of 20 Hz, a 1000 μF
capacitor would be needed, which is physically large and costly.
By connecting a speaker in a bridged-output configuration, the
quiescent differential voltage across the speaker becomes nearly
zero, eliminating the need for the coupling capacitor.
SPEAKER EFFICIENCY AND LOUDNESS
The effective loudness of 1 W of power delivered into an 8 Ω
speaker is a function of speaker efficiency. The efficiency is
typically rated as the sound pressure level (SPL) at 1 meter in
front of the speaker with 1 W of power applied to the speaker.
Most speakers are between 85 dB and 95 dB SPL at 1 meter at
1 W. Table 7 shows a comparison of the relative loudness of
different sounds.
Table 7. Typical Sound Pressure Levels
Source of Sound
Threshold of Pain
Heavy Street Traffic
Cabin of Jet Aircraft
Average Conversation
Average Home at Night
Quiet Recording Studio
Threshold of Hearing
dB SPL
120
95
80
65
50
30
0
It can easily be seen that 1 W of power into a speaker can
produce quite a bit of acoustic energy.
相關PDF資料 |
PDF描述 |
|---|---|
| SSM2211SZ-REEL71 | Low Distortion, 1.5 W Audio Power Amplifier |
| SSM2211CP-R2 | Low Distortion, 1.5 W Audio Power Amplifier |
| SSM2211CP-REEL | Low Distortion, 1.5 W Audio Power Amplifier |
| SSM2211CP-REEL7 | Low Distortion, 1.5 W Audio Power Amplifier |
| SSM2211CPZ-R21 | Low Distortion, 1.5 W Audio Power Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SSM2211SZ-REEL7 | 功能描述:IC AMP AUDIO PWR 1W MONO 8SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 標準包裝:2,000 系列:- 類型:AB 類 輸出類型:2 通道（立體聲） 在某負載時最大輸出功率 x 通道數量:- 電源電壓:4 V ~ 18 V 特點:- 安裝類型:通孔 供應商設備封裝:8-DIP 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 |
| SSM2211SZ-REEL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Distortion, 1.5 W Audio Power Amplifier |
| SSM2212 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Audio, Dual-Matched NPN Transistor |
| SSM2212RZ | 功能描述:IC TRANS AUDIO DUAL NPN 8SOIC RoHS:是 類別:分離式半導體產品 >> 晶體管(BJT) - 陣列 系列:- 標準包裝:10,000 系列:- 晶體管類型:2 NPN（雙） 電流 - 集電極 (Ic)（最大）:100mA 電壓 - 集電極發射極擊穿（最大）:45V Ib、Ic條件下的Vce飽和度（最大）:600mV @ 5mA，100mA 電流 - 集電極截止（最大）:- 在某 Ic、Vce 時的最小直流電流增益 (hFE):200 @ 2mA，5V 功率 - 最大:250mW 頻率 - 轉換:250MHz 安裝類型:表面貼裝 封裝/外殼:6-TSSOP，SC-88，SOT-363 供應商設備封裝:PG-SOT363-6 包裝:帶卷 (TR) 其它名稱:SP000747402 |
| SSM2212RZ-R7 | 功能描述:IC TRANS AUDIO DUAL NPN 8SOIC RoHS:是 類別:分離式半導體產品 >> 晶體管(BJT) - 陣列 系列:- 標準包裝:10,000 系列:- 晶體管類型:2 NPN（雙） 電流 - 集電極 (Ic)（最大）:100mA 電壓 - 集電極發射極擊穿（最大）:45V Ib、Ic條件下的Vce飽和度（最大）:600mV @ 5mA，100mA 電流 - 集電極截止（最大）:- 在某 Ic、Vce 時的最小直流電流增益 (hFE):200 @ 2mA，5V 功率 - 最大:250mW 頻率 - 轉換:250MHz 安裝類型:表面貼裝 封裝/外殼:6-TSSOP，SC-88，SOT-363 供應商設備封裝:PG-SOT363-6 包裝:帶卷 (TR) 其它名稱:SP000747402 |
發布緊急采購，3分鐘左右您將得到回復。