- 您現在的位置：買賣IC網 > PDF目錄297432 > SQE48T40025-NDB0 (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | SQE48T40025-NDB0 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, ONE-EIGHTH BRICK PACKAGE-8 |
| 文件頁數： | 11/13頁 |
| 文件大?。?/td> | 764K |
| 代理商： | SQE48T40025-NDB0 |
SQE48T40025 DC-DC Converter
36-75 VDC Input; 2.5 VDC @ 40 A Output
Preliminary Data Sheet
Protection Features
Input Undervoltage Lockout
Input undervoltage lockout is standard with this
converter. The converter will shut down when the
input voltage drops below a pre-determined voltage.
The input voltage must be typically 34 V for the
converter to turn on. Once the converter has been
turned on, it will shut off when the input voltage
drops typically below 33 V. This feature is beneficial
in preventing deep discharging of batteries used in
telecom applications.
Output Overcurrent Protection (OCP)
The converter is protected against overcurrent or
short circuit conditions. Upon sensing an overcurrent
condition, the converter will switch to constant
current operation and thereby begin to reduce output
voltage.
If the converter is equipped with the special OCP
version designated by the suffix K in the part
number,
the
converter
will
shut
down
in
approximately 15ms after entering the constant
current mode of operation. The standard version
(suffix 0) will continue operating in the constant
current mode until the output voltage drops below
60% at which point the converter will shut down as
shown in Figure 14.
Once the converter has shut down, it will attempt to
restart nominally every 200 ms with a typical 3-5%
duty cycle as shown in Figure 15. The attempted
restart will continue indefinitely until the overload or
short circuit conditions are removed or the output
voltage rises above 40-50% of its nominal value.
Once the output current is brought back into its
specified range, the converter automatically exits the
hiccup mode and continues normal operation.
Output Overvoltage Protection (OVP)
The converter will shut down if the output voltage
across Vout(+) (Pin 8) and Vout(-) (Pin 4) exceeds
the threshold of the OVP circuitry. The OVP circuitry
contains its own reference, independent of the output
voltage regulation loop. Once the converter has shut
down, it will attempt to restart every 200 ms until the
OVP condition is removed.
Overtemperature Protection (OTP)
The
converter
will
shut
down
under
an
overtemperature condition to protect itself from
overheating caused by operation outside the thermal
derating curves, or operation in abnormal conditions
such as system fan failure. Converter with the non-
latching option will automatically restart after it has
cooled to a safe operating temperature.
Safety Requirements
The
converters
meet
North
American
and
International safety regulatory requirements per
UL60950 and EN60950. Basic Insulation is provided
between input and output.
The converters have no internal fuse. If required, the
external fuse needs to be provided to protect the
converter from catastrophic failure.
Refer to the
“Input Fuse Selection for DC/DC converters”
application note on www.power-one-com for proper
selection of the input fuse. Both input traces and the
chassis ground trace (if applicable) must be capable
of conducting a current of 1.5 times the value of the
fuse without opening. The fuse must not be placed
in the grounded input line.
Abnormal
and
component
failure
tests
were
conducted with the input protected by a TBD fuse. If
a fuse rated greater than TBD A is used, additional
testing may be required.
To protect a group of
converters with a single fuse, the rating can be
increased from the recommended value above.
Electromagnetic Compatibility (EMC)
EMC requirements must be met at the end-product
system level, as no specific standards dedicated to
EMC characteristics of board mounted component
DC-DC converters exist. However, Power-One tests
its converters to several system level standards,
primary of which is the more stringent EN55022,
Information
technology
equipment
-
Radio
disturbance characteristics-Limits and methods of
measurement.
An effective internal LC differential filter significantly
reduces input reflected ripple current, and improves
EMC.
With the addition of a simple external filter, the
SQE48T40025 converter passes the requirements of
Class B conducted emissions per EN55022 and FCC
requirements.
Contact
Power-One
Applications
Engineering for details of this testing.
ZD-01723 Rev 1.1
www.power-one.com
Page 7 of 13
相關PDF資料 |
PDF描述 |
|---|---|
| SR3050PT | 15 A, 50 V, SILICON, RECTIFIER DIODE, TO-247AD |
| SR3020PT | 15 A, 20 V, SILICON, RECTIFIER DIODE, TO-247AD |
| SR305AA100D | FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, WIRE WRAP, SOCKET |
| SR305AA100U | FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, WIRE WRAP, SOCKET |
| SR305AA30D | FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, WIRE WRAP, SOCKET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SQE48T50012-NDA0 | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| SQE48T50012-NDA0G | 功能描述:DC/DC轉換器 1.2Vout 50A 1.2Vout 50A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| SQE5-P | 制造商:Power-One 功能描述: |
| SQETHERNET | 制造商:Intel 功能描述: |
| SQF620001 | 功能描述:OSC 156.25MHZ 3.3V HCSL SMD RoHS:是 類別:晶體和振蕩器 >> 振蕩器 系列:SaRonix-eCera™ SQ 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR |
發布緊急采購，3分鐘左右您將得到回復。