- 您現在的位置：買賣IC網 > PDF目錄372190 > SP6685ER Charge Pump LED Driver For Camera Flash PDF資料下載
參數資料
| 型號： | SP6685ER |
| 元件分類： | LED驅動器 |
| 英文描述： | Charge Pump LED Driver For Camera Flash |
| 中文描述： | 電荷泵的LED相機閃光燈驅動器 |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 143K |
| 代理商： | SP6685ER |
8
Date: 12/15/04
SP6685 Charge Pump LED Driver for Camera Flash Copyright 2004 Sipex Corporation
For an example of 200mA Torch mode and
600mA Flash mode, the values R
=
0.25
, V
= 150mV (Flash Mode), and
R
= 88.7K are calculated. The power
obtained in the Flash mode would be:
P
FLASH
= V
FB
*I
OUT
= 150mV*600mA = 90mW.
The typical 0603 surface mount resistor is
rated 1/10 watt continuous power and 1/5
watt pulsed power, more than enough for
this application. For other applications, the
P
can be calculated from the resistor
size selected. The R
resistor is recom-
mended to be size 0603 for most applica-
tions.
COMPONENT SELECTION
The sense resistor R
is determined by
the value needed in the Torch mode for the
desired output current by the equation:
R
= V
FB
/ I
OUT
where V
FB
= 50mV (Torch
Mode)
The SP6685 charge pump circuit requires 3
capacitors: input, output and fly capacitor,
and a 1
μ
F value is typically recommended.
For the input capacitor, a larger value of
2.2
μ
F or 4.7
μ
F will help reduce input volt-
age ripple for applications sensitive to ripple
on the battery voltage. All the capacitors
should be ceramic to obtain low ESR, which
improves bypassing on the input and output
and improves output voltage drive by reduc-
ing output resistance. X5R or X7R Ceramic
capacitors are recommended for most ap-
plications. A selection of recommended
capacitors is included in Table 1. The input
and output capacitors should be located as
close to the V
and V
pins as possible to
obtain best bypassing, and the returns
should be connected directly to the P
pin
or to the thermal pad ground located under
the SP6685. The fly capacitor should be
located as close as possible to the C1 and
C2 pins as possible.
Once the R
resistor has been selected
for Torch mode, the V
voltage can be
selected for Flash mode using the following
equation:
V
= I
*R
(Flash Mode) where I
OUT
is
for Flash Mode
Next, the R
resistor can be selected for
Flash mode using the following equation:
R
SET
= (1.26V/ V
FB
)*11.2K
(Flash Mode)
Part Reference
U1
CIN
COUT, CF
RSET
RSENSE
Part Number
SP6685ER
GRM188R0J475KE19
GRM155R60J105KE19B
-
-
Value
Size
Manufacturers/ Website
Sipex/www.sipex.cpm
Murata/www.murata.com
Murata/www.murata.com
any
any
3x3mm DFN - 10 pin
0603/X5R/0.9mm ht
0402/X5R/0.5mm ht
0402
0603
4.7uF/6.3V
1uF/6.3V
88.7K
0.22ohms
相關PDF資料 |
PDF描述 |
|---|---|
| SP6690 | Micro Power Boost Regulator Series White LED Driver |
| SP6690EB | Evaluation Board Manual |
| SP6690EK | Micro Power Boost Regulator Series White LED Driver |
| SP6690ER | Micro Power Boost Regulator Series White LED Driver |
| SP6690EU | Evaluation Board Manual |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6685ER/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:700mA Buck/Boost Charge Pump LED Driver |
| SP6685ER-L | 功能描述:電荷泵 Camera Flash RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| SP6685ER-L/TR | 功能描述:電荷泵 700mA For Camera Flash RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| SP6685ERTR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Charge Pump LED Driver For Camera Flash |
| SP6686 | 制造商:EXAR 制造商全稱:EXAR 功能描述:400mA Buck/Boost Charge Pump LED Driver |
發布緊急采購，3分鐘左右您將得到回復。