參數資料
型號: sp6661
英文描述: High Frequency 200mA Charge Pump Inverter or Doubler(高效率,200mA電荷泵(反向器/倍壓器))
中文描述: 高頻200mA的充電泵逆變器或倍增(高效率,200mA的電荷泵(反向器/倍壓器))
文件頁數: 2/5頁
文件大小: 51K
代理商: SP6661
rev. 4/12/01
SP6661 Evaluation Board Manual
2
Copyright 2001 Sipex Corporation
BOARD LAYOUT
The
SP6661 Evaluation Board
has been
designed to easily and conveniently provide
access to all Inputs and Outputs of the
SP6661 device under test. Position the
board with the silkscreen lettering upright
(also see the drawing on the front page of
this manual) and you will see two circuits –
the Doubler Circuit on top, and the Inverter
Circuit below. Also, note the Doubler Circuit
is followed by an LDO Circuit, producing a
5V regulated output from a 3V input to the
Doubler. The Input and Output connections
are made with raised female pin receptacles
which can accommodate easy-hook con-
nection leads for power and meter connec-
tions, as well as scope probe hooks and
grounds for waveform measurements.
USING THE EVALUATION BOARD
Connect the
SP6661 Evaluation Board
Doubler Circuit or Inverter Circuit to a posi-
tive power supply for V
IN
. It is good practice
to not switch power on until power connec-
tions are made to the evaluation board.
Evaluating Doubler Circuit
V
IN
— U1-3 — Connect to external supply
V
IN
= +2.5 to +5.0V.
GND — U1-5 — Connect to external supply
GND.
CAP+ — U1-2 — Use to monitor Charge
Pump Frequency (1/2 OSC pin frequency).
V
OUT
— U1-8 — Connect to Load, Meter or
Scope. V
OUT
= +5.0 to +10.0V.
GND — U1-5 — Connect to Load, Meter or
Scope GND.
FC — U1-1 — Connect to OPEN for Low
Frequency, to V
OUT
for High Frequency.
SP6661 EVALUATION BOARD
Evaluating Doubler Circuit with 5V LDO
Regulator
Same connections as Doubler above, but
with additional LDO outputs:
+5 — U2-5 — Connect to Load, Meter or
Scope. V
OUT
= +5.0V.
GND — U2-2 — Connect to Load, Meter or
Scope GND.
Evaluating Inverter Circuit
V
IN
— U3-8 — Connect to external supply
V
IN
= +1.5 to +5.0V.
GND — U3-3 — Connect to external supply
GND.
CAP+ — U3-2 — Use to monitor Charge
Pump Frequency (1/2 OSC pin frequency).
V
OUT
— U3-5 — Connect to Load, Meter or
Scope. V
OUT
= -1.5 to –5.0V.
GND — U3-3 — Connect to Load, Meter or
Scope GND.
FC — U3-1 — Connect to OPEN for Low
Frequency, to V
OUT
for High Frequency.
Evaluating Oscillator Performance with
Inverter or Doubler Circuit
To accurately measure the internal oscilla-
tor frequency at pin 7 is extremely difficult,
since any connection to this pin may induce
capacitance which will change the frequency
(1/RoscCosc). It is for this reason that the
SP6661 Evaluation Board has only a small
pad connection to it and not a pin receptacle.
Alternatively, you can measure the charge
pump frequency at the CAP+ pin, which
equals _ the OSC pin frequency.
To run the Inverter or Doubler Circuit at other
frequencies, the OSC pin can be driven with
an external oscillator with a square wave of
0 to V
IN
volts. Tests have shown that typi-
cally the circuits can perform up to oscillator
frequencies of 900kHz.
相關PDF資料
PDF描述
sp6121 Low Voltage, 8 Pin, Synchronous Buck Controller(低壓,8引腳,同步補償控制器)
SP6680EB Evaluation Board Manual
SP6680EU High Efficiency Buck/Boost Charge Pump Regulator
SP6680TR High Efficiency Buck/Boost Charge Pump Regulator
SP6680 High Efficiency Charge Pump Regulator(高效電荷泵穩壓器)
相關代理商/技術參數
參數描述
SP66619 制造商:L-com Inc 功能描述:DB15F CUTEND 24AWG SOLID 16FT
SP6661CN-L 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
SP6661EB 功能描述:電源管理IC開發工具 Eval Board for SP6661 Series RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
SP6661EN 功能描述:開關變換器、穩壓器與控制器 High Frequency 200mA Inverter or Doubler RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
SP6661EN/TR 功能描述:開關變換器、穩壓器與控制器 High Frequency 200mA Inverter or Doubler RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel