參數資料
型號： SI2494-A-GM
廠商： Silicon Laboratories Inc
文件頁數： 22/70頁
文件大?。?/td> 0K
描述： IC ISOMODEM 56KBPS 38-QFN
標準包裝： 364
系列： *
Si2494/39
Rev. 1.0
29
Vn
Result code type (see Table 14 on page 49).
V0
Numeric result codes.
V1
Verbal result codes
Xn
Call Progress Monitor (CPM)—This command controls which CPM signals are monitored
and reported to the host from the Si2494/39. (See Table 14 on page 49.)
X0
Basic results; disable CPM—Blind dial (does not wait for dial tone). CONNECT message
does not include speed.
X1
Extended results; disable CPM—Blind dial. CONNECT message includes speed.
X2
Extended results and detect dial tone only—Add dial tone detection to X1 mode. Does not
blind dial.
X3
Extended results and detect busy only—Add busy tone detection to X1 mode.
X4
Extended results, full CPM—Full CPM enabled, CONNECT message includes speed.
X5
Extended results—Full CPM enabled including ringback detection. Adds ringback detection
to X4 mode.
Yn
Long space disconnect—Modem hangs up after 1.5 seconds or more of continuous space
while on-line.
Y0
Disable.
Y1
Enable.
Z
Hard Reset—This command is functionally equivalent to pulsing the RESET pin low. (See
:E
Read from serial EEPROM.
:I
Interrupt Read—This command causes the ISOmodem to report the lower 8 bits of the
interrupt register I/O Control 0 (U70). The CID, OCD, PPD, and RI bits also are cleared, and
the INT pin (INT bit in parallel mode) is deactivated on this read.
:M
Write to serial EEPROM.
:P
Program RAM Write—This command is used to upload firmware supplied by Silicon Labs to
the Si2494/39. The format for this command is AT:Paaaa,xxxx,yyyy,.... where aaaa is the first
address in hexadecimal and xxxx,yyyy,.... is data in hexadecimal. Only one :P command is
allowed per AT command line. No other commands can be concatenated in the :P command
line. This command is only for use with special files provided by Silicon Laboratories. Do not
attempt to use this command for any other purpose.
:R
User-Access Register Read—This command allows the user to read from the user-access
registers (see "6. User-Access Registers (U-Registers)" on page 54). The format is “AT:Raa”,
where:
aa = user-access address in hexadecimal.
The “AT:R” command causes all the U- registers to be displayed.
:U
User-Access Register Write—This command allows the user to write to the 16-bit user-
access registers. (See page page 54.) The format is “AT:Uaa,xxxx,yyyy,zzzz,...” where
aa = user-access address in hexadecimal.
xxxx = Data in hexadecimal to be written to location aa.
yyyy = Data in hexadecimal to be written to location (aa + 1).
zzzz = Data in hexadecimal to be written to location (aa + 2).
etc.
Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued)
Command
Action
相關PDF資料
PDF描述
SI3000-C-GS IC VOICE CODEC 3.3V/5V 16SOIC
SI3011-F-FS IC VOICE DAA GCI/PCM/SPI 16SOIC
SI3012-KS IC LINE-SIDE DAA 16SOIC
SI3019-F-FS IC LINE-SIDE DAA 16SOIC
SI3019-F-GM IC VOICE GLOBAL DAA PROGR 20QFN
相關代理商/技術參數
參數描述
SI2494-A-GMR 制造商:Silicon Laboratories Inc 功能描述:56 KBPS, V.92 ISOMODEM +VOICE SYSTEM-SIDE - LEAD-FREE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC ISOMODEM 56KBPS 38-QFN
SI24R1 制造商:SIRECTIFIER 制造商全稱:Sirectifier Semiconductors 功能描述:完全兼容 NRF24L01P,超低功耗高性能 2.4GHz GFSK 無線收發芯片
SI24S 制造商:IBase Technology (USA) Inc. 功能描述:(DS), ULTRA SLIM BOOK-SIZE EMBEDDED SYSTEM WITH W/ AMD K8 (B - Bulk
SI24SD 制造商:IBase Technology (USA) Inc. 功能描述:(DS), ULTRA SLIM BOOK-SIZE EMBEDDED SYSTEM WITH W/ AMD ATHLO - Bulk
SI24XX-LOGTOOL 功能描述:TOOL MODEM LOG SI24XX RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*