參數資料
型號： SI2493-D-GT
廠商： Silicon Laboratories Inc
文件頁數： 16/60頁
文件大小： 0K
描述： IC ISOMODEN GLOBAL DAA 24TSSOP
標準包裝： 62
系列： *
Si2493
Rev. 1.3
23
Table 8. Basic AT Command Set (Command Defaults in Bold)
Command
Action
$
Display AT command mode settings.
A
Answer incoming call
A/
Re-execute last command. This is the only command not preceded by “AT” or followed by a
<CR>.
Dn
Dial
The dial command, followed by 1 or more dial command modifiers, manually dials a phone
number:
Modifier
Function
! or &
Flash hook switch for FHT (U4F) ms (default: 500 ms)
, or <
Pause before continuing for S8 seconds (default:
2 seconds)
;
Return to AT command mode
@
Wait for silence.
G
Polarity reversal detect. By placing the “G” character in
the dial string (i.e. ATDTG1), the Si2493 will monitor the
telephone line for polarity reversals. If a busy tone is
detected, the Si2493 will report “POLARITY REVER-
SAL” if a polarity reversal was detected or “NO POLAR-
ITY REVERSAL” if a polarity reversal was not detected.
In each case, the result code is followed by “OK”. If the
S7 timeout occurs before a busy tone is detected, the
Si2493 will report “NO CARRIER”. Polarity reversal
monitoring begins after the last digit is dialed and ends
when the busy tone is detected or S7 timeout occurs.
Note: It is not possible to establish a modem connection
when using this command.
L
Redial last number.
P
Pulse (rotary) dialing—pulse digits: 0, 1, 2, 3, 4, 5, 6, 7,
8, 9
T
Tone (DTMF) dialing—DTMF digits: *, #, A, B, C, D, 0,
1, 2, 3, 4, 5, 6, 7, 8, 9.
W
Wait for dial tone before continuing for S14 seconds
(default: 12 seconds). Blind dialing modes X0, X1 and
X3 do not affect the W command.
If the DOP bit (U7A, bit 7) is set, the “ATDTW” com-
mand will cause the ISOmodem to pause dialing and
either report an “OK” if a dialtone is detected or “NO
DIALTONE” if a dial tone is not detected.
En
Local DTE echo
E0
Disable
E1
Enable
Hn
Hook switch.
H0
Go on-hook (hang up modem).
相關PDF資料
PDF描述
SI2494-A-GM IC ISOMODEM 56KBPS 38-QFN
SI3000-C-GS IC VOICE CODEC 3.3V/5V 16SOIC
SI3011-F-FS IC VOICE DAA GCI/PCM/SPI 16SOIC
SI3012-KS IC LINE-SIDE DAA 16SOIC
SI3019-F-FS IC LINE-SIDE DAA 16SOIC
相關代理商/技術參數
參數描述
SI2493-D-GTR 制造商:Silicon Laboratories Inc 功能描述:56 KBPS, V.92 ISOMODEM SYSTEM-SIDE - LEAD-FREE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC ISOMODEN GLOBAL DAA 24TSSOP 制造商:Silicon Laboratories Inc 功能描述:56 kbps V92 ISOmodem System-Side PBF
Si2493-E-FT 制造商:SILABS 制造商全稱:SILABS 功能描述:Evaluation Board Rev 5.0 for the Si2493/57/34/15/04
Si2493FS08-EVB 功能描述:網絡開發工具 16-pin Si2493+Si3008 ISOmodem Eval Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
Si2493FS18-EVB 功能描述:網絡開發工具 16-pin Si2493+Si3018 ISOmodem Eval Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
SI2493-FT 功能描述:電信線路管理 IC CONTACT SILICON LABS FOR AVAILABILITY RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*