- 您現在的位置：買賣IC網 > PDF目錄16381 > SI2401FS10-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 UART INTERFACE PDF資料下載
參數資料
| 型號： | SI2401FS10-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 22/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL SI2401 UART INTERFACE |
| 標準包裝： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 電信，調制解調器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2401 |
| 主要屬性： | 雙路 RJ-11 連接至電話線路，音頻連接器 |
| 次要屬性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，調制解調器，電源 |
| 相關產品： | 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名稱： | 336-1167 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
Si2401
Rev. 1.0
29
5.5.1. Automatic Call Progress Detection
The Si2401 has the ability to detect dial, busy, and
ringback
tones automatically. The following is a
description
of
the
algorithms
that
have
been
implemented for these three tones.
Dial Tone
. The dial tone detector looks for a dial
tone after going off-hook and before dialing is
initiated. This can be bypassed by enabling blind
dialing (set S07[6] (BD) = 1b). After going off-hook,
the Si2401 waits the number of seconds in S01
(DW) before searching for the dial tone.
In order for a dial tone to be detected, it must be
present for the length of time programmed in S1C
(DTT). Once the dial tone is detected, dialing
commences. If a dial tone is not detected within the
time programmed in S02 (CW), the Si2401 hangs up
and echoes an “n” to the user.
Busy/Ringback Tone
. After dialing has completed,
the Si2401 monitors for Busy/Ringback and modem
answer tones. The busy and ringback tone detectors
both use the call progress energy detector. The
registers that set the cadence for busy and ringback
are listed in Table 15. Si2401 register settings for
global cadences for busy and ringback tones are
listed in Table 16.
5.5.2. Manual Call Progress Detection
Because other call progress tones beyond those
described above may exist, the Si2401 supports manual
call progress. This requires the host to read and write
the low-level DSP registers and may require real time
control by the host. Manual call progress may be
required for detection of application-specific ringback,
dial tone, and busy signals. The section on DSP low-
level control should be read before attempting manual
call progress detection.
The call progress biquad filters can be programmed to
have a custom frequency response and detection level
(as described in "6. Low Level DSP Control" on page
Four dedicated user-defined frequency detectors can
be programmed to search for individual tones. The four
detectors have center frequencies that can be set by
registers UDFD1–4 (see Table 18). SE5[6] [TDET]
[SE8 = 0x02] Read Only Definition can be monitored,
along with TONE, to detect energy at these user-
defined frequencies. The default trip-threshold for
UDFD1–4 is –43 dBm but can be modified with the DSP
register, UDFSL.
By issuing the “ATDT;” command, the modem goes off-
hook and returns to command mode. The user can then
put the DSP into call progress monitoring by first setting
SE8 = 0x02. Next, set SE5 (DSP2) = 0x00 so that no
tones are transmitted, and set SE6 (DSP3) to the
appropriate code, depending on which types of tones
are to be detected.
At this point, users may program their own algorithm to
monitor the detected tones. If the host wishes to dial, it
should do so by blind dialing, setting the dial timeout
S01 (DW)
to
0
seconds,
and
issuing
an
“ATDT<Phone Number>;<CR>”
command.
This
immediately causes the ISOmodem chipset to dial and
return to command mode.
Once the host has detected an answer tone using
manual call progress, the host should immediately
execute the “ATDT” command in order to make a
connection. This causes the Si2401 to search for the
modem answer tone and begin the correct connect
sequence.
In manual call progress, the DSP can be programmed
to detect specific tones. The result of the detection is
reported in SE5 (SE8 = 0x2) as explained above. The
output is priority-encoded such that if multiple tones are
detected, the one with the highest priority whose
detection is also enabled is reported (see SE5 [SE8=02]
Read Only.)
In manual call progress, the DSP can be programmed
to generate specific tones (see SE5[2:0] (TONC)
(SE8 = 02)
Write
Only).
For
example,
setting
SE5[2:0] (TONC) = 110b generates the user-defined
tone (as indicated by UFRQ in Table 18) with an
amplitude of TGNL.
Table 17 shows the mappings of Si2401 DTMF values,
keyboard equivalents, and the related dual tones.
Table 15. Busy and Ringback Cadence
Registers
Register Name
Function
Units
S16
BTON
Busy tone on time
10 ms
S17
BTOF
Busy tone off time
10 ms
S18
BTOD
Busy tone delta time
10 ms
S19
RTON
Ringback tone on time
53.333
ms
S1A
RTOF
Ringback tone off time
53.333
ms
S1B
RTOD Ringback tone delta time
53.333
ms
相關PDF資料 |
PDF描述 |
|---|---|
| UPA0J272MPD1TD | CAP ALUM 2700UF 6.3V 20% RADIAL |
| UPA0J222MPD1TD | CAP ALUM 2200UF 6.3V 20% RADIAL |
| GBC19DRAS | CONN EDGECARD 38POS R/A .100 SLD |
| CM322522-2R2JL | INDUCTOR CHIP 2.2UH 3225 SMD |
| RR70G821MDN1 | CAP ALUM 820UF 4V 20% RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI2401-FSR | 功能描述:電信線路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI2401URT-EVB | 功能描述:網絡開發工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| SI2403 | 制造商:SILABS 制造商全稱:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
| SI2404 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA |
發布緊急采購，3分鐘左右您將得到回復。