- 您現(xiàn)在的位置：買賣IC網 > PDF目錄16381 > SI2400URT-EVB (Silicon Laboratories Inc)BOARD EVAL FOR SI2400 ISOMODEM PDF資料下載
參數資料
| 型號： | SI2400URT-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 25/94頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR SI2400 ISOMODEM |
| 標準包裝： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 電信，調制解調器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2400 |
| 主要屬性： | 雙路 RJ-11 連接至電話線路，音頻連接器 |
| 次要屬性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，調制解調器，電源 |
| 相關產品： | SI2400-BS-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC SI2400-FS-ND - IC ISOMODEM SYST-SIDE DAA 16SOIC 336-1093-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名稱： | 336-1166 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
Si2400
Rev. 1.3
31
This command causes the modem to echo the chip
revision for the Si2400 device.
0 = Revision A
1 = Revision B
2 = Revision C, etc.
M
Speaker On/Off Options
These options are used to control AOUT for use with a
call progress monitor speaker.
M0
Speaker always off.
M1
Speaker on until carrier established. The modem sets
SF4[3:2] (ARL) = 11b and SF4[1:0] (ATL) = 11b after a
connection is established.
M2
Speaker always on.
M3
Speaker on after last digit dialed, off at carrier detect.
O
Return to Online Mode
This command returns the modem to the online mode. It
is frequently used after an escape sequence to resume
communication with the remote modem.
RO
Turn-Around
This command initiates a V.23 “direct turnaround”
sequence and returns online.
6.4. S-Register Control
S-registers control Si2400 configuration and provide
status information. Therefore, writing to and reading
from S-registers is central to the operation of the
modem. There are two fundamental methods for writing
to and reading from Si2400 S-Registers. The first and
most common method uses the ATSR=N and ATSR?
commands.
These
commands
are
used
by
communication software packages and are universally
supported by modem chips. The second method uses
the ATw##, ATr#, ATm#, and ATq# commands and is
designed
to
reduce
data
flow
and
streamline
performance in embedded systems. When ATSR
commands are used, each character of the two
character hexadecimal values for both R and N are sent
to the AT command parser for decoding and action
immediately instead of waiting for a <CR>. Additionally,
a carriage return, <CR>, is required to terminate the
ATSR?
command
(not
ATSR=N).
When
the
#
commands are used, # is the single character ASCII
equivalent of the two character hexadecimal S-Register
address or value and no carriage return is required for
any of the # commands. Further explanations and
examples are given below.
6.4.1. ATSR Commands
The ATSR commands are generally used to write to or
read from S-registers. The address, R, and the value, N,
must be written into the AT command as a two character
hexadecimal value between 00 and FF. An S-Register is
written with the command “ATSR=N”. The hexadecimal
address and value parameters appearing on the
terminal or PC screen are actually transmitted to the
modem as the hexadecimal equivalents of each
character. Likewise, the value N stored in S-register R is
read back to the terminal with the ATSR? command as
two hexadecimal characters. For example, read the
value of S35 after the Si2400 has been reset.
6.4.2. # Commands
The # commands offer several performance and
convenience advantages for embedded applications
over the more traditional ATSR-style commands. The #
parameter is entered as the ASCII equivalent of a
hexadecimal value representing the S-register address
or content. This parameter is sent to the modem as the
hexadecimal equivalent of the ASCII value. The #
commands offer a more rapid method for reading and
writing S-Registers since fewer characters are sent to or
received from the modem.
6.4.3. w## Write S-Register
This command is analogous to the ATSR=N command.
From a terminal, the first # following w is the ASCII
equivalent of the hexadecimal address of the S-Register
and the second # is the ASCII equivalent of the
hexadecimal value of the S-Register. For example, write
the value 58h to S34.
6.4.4. r# Command Read S-Register
This command is analogous to the ATSR? command.
From a terminal, the # following r is the ASCII
equivalent of the hexadecimal address of the S-
Register. The modem will echo the register contents as
the ASCII equivalent of the hexadecimal value of the
contents. This command executes immediately and
does not require a carriage return. Modem result codes
Terminal
Entry
Sent to Modem Response Display
ATS35?<CR>
41 54 53 33 35
3F 0D
41 32
A2
Terminal
Entry
Sent to Modem
(hex)
Response Display
ATw4X
41 54 77 34 58
—
相關PDF資料 |
PDF描述 |
|---|---|
| CM322522-1R8JL | INDUCTOR CHIP 1.8UH 3225 SMD |
| 496837-000 | CABLE TERMINATION RG/U 178,404 |
| VI-J72-EX | CONVERTER MOD DC/DC 15V 75W |
| 6374615-8 | C/A LC-SC DUP 62.5/125, 8M |
| VE-B12-EY-S | CONVERTER MOD DC/DC 15V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI2401 | 制造商:SILABS 制造商全稱:SILABS 功能描述:V.22BIS ISOMODEM㈢ WITH LOW-COST DAA |
| SI2401-C-FS | 制造商:Silicon Laboratories Inc 功能描述: |
| SI2401DC-EVB | 功能描述:子卡和OEM板 SI2401 Daughter Card RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| SI2401-FS | 功能描述:電信線路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| Si2401FS08-EVB | 功能描述:網絡開發(fā)工具 Si2401+Si3008 ISO modem Eval Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
發(fā)布緊急采購，3分鐘左右您將得到回復。