- 您現在的位置：買賣IC網 > PDF目錄385829 > SD2D-DC5V POLARISED, MONOSTABLE SAFETY RELAY PDF資料下載
參數資料
| 型號： | SD2D-DC5V |
| 英文描述： | POLARISED, MONOSTABLE SAFETY RELAY |
| 中文描述： | 極化，單穩態安全繼電器 |
| 文件頁數： | 5/5頁 |
| 文件大?。?/td> | 247K |
| 代理商： | SD2D-DC5V |
Pure DC current should be applied to the
coil. The wave form should be rectangular.
If it includes ripple, the ripple factor should
be less than 5%. However, check it with
the actual circuit since the characteristics
may be slightly different.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
3. Cleaning
For automatic cleaning, the boiling
method is recommended. Avoid ultrasonic
cleaning which subjects the relays to high
frequency vibrations, which may cause
the contacts to stick.
It is recommended that a
fl
uorinated
hydrocarbon or other alcoholic solvents
be used.
4. Soldering
We recommend the following soldering
conditions
1) Automatic soldering
1) Preheating: 100
°
C
212
°
F
, max. 60 s
2) Soldering: 250
°
C
482
°
F
, max. 5 s
5. Others
1) If the relay has been dropped, the
appearance and characteristics should
always be checked before use.
2) The cycle lifetime is de
fi
ned under the
standard test condition speci
fi
ed in the
JIS* C 5442-1986 standard (temperature
15 to 35
°
C
59 to 95
°
F
, humidity 25 to
85%). Check this with the real device as it
is affected by coil driving circuit, load type,
activation frequency, activation
phase,ambient conditions and other
factors.
Also, be especially careful of loads such
as those listed below.
(1) When used for AC load-operating and
the operating phase is synchronous.
Rocking and fusing can easily occur due
to contact shifting.
(2) High-frequency load-operating
closing of the relay is performed with a
load that causes arcs at the contacts,
nitrogen and oxygen in the air is fused by
the arc energy and HNO
3
is formed. This
can corrode metal materials.
Three countermeasures for these are
listed here.
1. Incorporate an arc-extinguishing
circuit.
2. Lower the operating frequency
3. Lower the ambient humidity
3) For secure operations, the voltage
applied to the coil should be nominal
voltage. In addition, please note that pick-
up and drop-out voltage will vary
according to the ambient temperature and
operation conditions.
4) Heat, smoke, and even a
fi
re may occur
if the relay is used in conditions outside of
the allowable ranges for the coil ratings,
contact ratings, operating cycle lifetime,
and other speci
fi
cations. Therefore, do
not use the relay if these ratings are
exceeded. Also, make sure that the relay
is wired correctly.
5) Incorrect wiring may cause unexpected
events or the generation of heat or
fl
ames.
6) Check the ambient conditions when
storing or transporting the relays and
devices containing the relays. Freezing or
condensation may occur in the relay,
causing functional damage. Avoid
subjecting the relays to heavy loads, or
strong vibration and shocks.
6. Usage, transport and storage
conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
–
40 to +70
°
C
–
40 to +158
°
F
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage:
2) Condensation
Condensation forms when there is a
sudden change in temperature under high
temperature and high humidity conditions.
Condensation will cause deterioration of
the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the
temperatures is lower than 0
°
C
32
°
F
. This
causes problems such as sticking of
movable parts or operational time lags.
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
Tolerance range
(Avoid
condensation when
used at temperatures
higher than 0
°
C
32
°
F
)
(Avoid freezing when
used at temperatures
lower than 0
°
C
32
°
F
)
85
5
–
40
–
40
0
+32
+158
Temperature,
°
C
°
F
Humidity, %R.H.
2/19/2003
All Rights Reserved, Copyright Matsushita Electric Works, Ltd.
Go To Online Catalog
相關PDF資料 |
PDF描述 |
|---|---|
| SD3000C | STANDARD RECOVERY DIODES Hockey Puk Version |
| SD300N | STANDARD RECOVERY DIODES Stud Version |
| SD300R | STANDARD RECOVERY DIODES Stud Version |
| SD300N16PC | STANDARD RECOVERY DIODES Stud Version |
| SD300N20PC | CAPACITOR, 82UF 16VCAPACITOR, 82UF 16V; Capacitance:82uF; Voltage rating, DC:16V; Capacitor dielectric type:; Series:SVP; Temp, op. max:105(degree C); Temp, op. min:-55(degree C); Tolerance, +:20%; Tolerance, -:20%; Current, ripple |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SD2EMI | 功能描述:電線導管 2 H PANELMAX NOISE SHIELD 3FT RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| SD2G-100X | 制造商:JVC Worldwide 功能描述:2G SDCARD 100X |
| SD2GB-133-381E | 制造商:Micron Technology Inc 功能描述:2GB MODULE MULTI LAYER CHIP - Trays |
| SD2H6 | 功能描述:電線導管 SLOTTD DUCT DIV WALL PVC 2"H X 6’ RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| SD2HWH6 | 制造商:Panduit Corp 功能描述:2" SLOTTED DIVIDER WALL - Shrink Tubing that comes in 4ft sticks 制造商:Panduit Corp 功能描述:SLOTTED DUCT DIVIDER PVC 2H X 6' 制造商:Panduit Corp 功能描述:Slotted Divider Wall, The Divider Wall Will Snap On |
發布緊急采購，3分鐘左右您將得到回復。