- 您現在的位置：買賣IC網 > PDF目錄374734 > SC621AEVB (Semtech Corporation) Charge Pump, 4 LEDs, 400mA Flash LED, Dual LDOs, and I2C Interface PDF資料下載
參數資料
| 型號： | SC621AEVB |
| 廠商： | Semtech Corporation |
| 英文描述： | Charge Pump, 4 LEDs, 400mA Flash LED, Dual LDOs, and I2C Interface |
| 中文描述： | 電荷泵，4個LED，400mA的閃光LED，雙LDO和I2C接口 |
| 文件頁數： | 15/24頁 |
| 文件大小： | 327K |
| 代理商： | SC621AEVB |
SC621A
15
Applications Information (continued)
Backlight Quiescent Current
The quiescent current required to operate all four
backlights is reduced by 1.5mA when backlight current
is set to 4.0mA or less. This feature results in higher
efficiency under light-load conditions. Further reduction
in quiescent current will result from using fewer than four
LEDs.
Fade-In and Fade-Out
Backlight brightness can be set to automatically fade-in
when current is set to increase and fade-out when current
is set to decrease. When enabled with a new current
setting, the current will step through each incremental
setting between the old and new values. The result is a
visually smooth change in brightness with a rate of fade
that can be set to 8, 16, 24, or 32 ms per step.
LED Flash and Spotlight Current Sink
A single output current sink is provided to drive both flash
and spotlight functions. In flash mode, this current sink
provides up to 400mA for a flash LED
or array of parallel
LEDs
. Flash current settings are in 50mA increments from
50mA to 400mA. The FLEN pin directly triggers the FLASH
function when pulled high, or it can be wired to VIN to
enable software control via the serial interface.
In spotlight mode, the output can be set for up to 250mA
of continuous current. Settings are available in 50mA
increments from 50mA to 250mA. Continuous operation
above 250mA is not recommended due to high power
dissipation.
Flash and Spotlight Safety Timer
A safety timer disables the flash and spotlight output
current sink if the sink remains active for an extended
period. The timer protects the SC621A and the LED from
high power dissipation that can cause overheating. The
timer’s default state is on, but the timer may be disabled
via the serial interface to allow continuous output current
in spotlight mode. The safety timer affects only the FL pin
and will turn off the sink after a period of 1 second. The
timer may be reset by either forcing the FLEN pin low
or by resetting the Flash/Spotlight control bits via the
interface.
Programmable LDO Outputs
Two low dropout (LDO) regulators are provided for
camera module I/O and core power. Each LDO has at least
100mA of available load current with ±3.5% accuracy. The
minimum current limit is 200mA, so outputs greater than
100mA are possible at somewhat reduced accuracy.
A 1μF, low ESR capacitor should be used as a bypass
capacitor on each LDO output to reduce noise and
ensure stability. In addition, it is recommended that a
minimum 22nF capacitor be connected from the BYP
pin to ground to minimize noise and achieve optimum
power supply rejection. A larger capacitor can be used
for this function, but at the expense of increasing turn-
on time. Capacitors with X7R or X5R ceramic dielectric
are strongly recommended for their low ESR and superior
temperature and voltage characteristics. Y5V capacitors
should not be used as their temperature coefficients
make them unsuitable for this application.
Shutdown State
The device is disabled when the EN pin is low. All registers
are reset to default condition when EN is low.
Sleep Mode
When all LEDs are off, sleep mode is activated. This is a
reduced current mode that helps minimize overall current
consumption by turning off the clock and the charge
pump while continuing to monitor the serial interface for
commands. Both LDOs can be powered up while in sleep
mode.
I
2
C Compatible Interface Functions
All device functions can be controlled via the I
2
C
compatible interface. The interface is described in detail
in the Serial I
nterface section
of the datasheet.
相關PDF資料 |
PDF描述 |
|---|---|
| SC621A | Charge Pump, 4 LEDs, 400mA Flash LED, Dual LDOs, and I2C Interface |
| SC621AULTRT | Charge Pump, 4 LEDs, 400mA Flash LED, Dual LDOs, and I2C Interface |
| SC621 | LED Light Management Unit Charge Pump, 4 LEDs, 400mA Flash LED, Dual LDOs, and SemWireTM Interface |
| SC621EVB | LED Light Management Unit Charge Pump, 4 LEDs, 400mA Flash LED, Dual LDOs, and SemWireTM Interface |
| SC621ULTRT | LED Light Management Unit Charge Pump, 4 LEDs, 400mA Flash LED, Dual LDOs, and SemWireTM Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC621AULTRT | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Charge Pump, 4 LEDs, 400mA Flash LED, Dual LDOs, and I2C Interface |
| SC621EVB | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:LED Light Management Unit Charge Pump,4 LEDs, 400mA Flash LED Dual LDOs,and SemWire Interface |
| SC621ULTRT | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:LED Light Management Unit Charge Pump,4 LEDs, 400mA Flash LED Dual LDOs,and SemWire Interface |
| SC622 | 制造商:M.E.C. Relays 功能描述: |
| SC622_09 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:LED Light Management Unit Charge Pump, 400mA Flash LED, Dual LDOs, and SemWire Interface |
發布緊急采購，3分鐘左右您將得到回復。