參數資料
型號： SC480IMLTRT
廠商： Semtech Corporation
英文描述： Complete DDR1/2/3 Memory Power Supply
中文描述： 完全DDR1/2/3內存供電
文件頁數： 19/25頁
文件大小： 858K
代理商： SC480IMLTRT
19
2006 Semtech Corp.
www.semtech.com
POWER MANAGEMENT
SC480
Application Information (Cont.)
accurate signal. The layout can be generally considered
in three parts; the control section referenced to VSSA, the
VTT output, and the switcher power section.
Looking at the control section
fi
rst, locate all components
referenced to VSSA on the schematic and place these
components at the chip. Connect VSSA using a wide
(>0.020”) trace. Very little current
fl
ows in the chip ground
therefore large areas of copper are not needed. Connect
the VSSA pin directly to the thermal pad under the device
as the only connection from PGND1 and PGND2 from
VSSA.
Decoupling capacitors for VCCA/VSSA and VDDP/PGND1
should be placed is as close as possible to the chip. The
feedback components connected to FB, along with the
VDDQ sense components, should also be located at the
chip. The feedback trace from the VDDQ output should
route from the top of the output capacitors, in a quiet
layer back to the FB components.
Next, looking at the switcher power section, there are a
few key guidelines to follow:
There should be a very small input loop, well
decoupled.
The phase node should be a large copper pour, but
still compact since this is the noisiest node.
Input power ground and output power ground should
not connect directly, but through the ground planes
instead.
1.
2.
3.
Finally, connecting the control and switcher power sections
should be accomplished as follows:
Route VDDQ feedback trace in a “quiet” layer, away
from noise sources.
Route DL, DH and LX (low side FET gate drive, high
side FET gate drive and phase node) to the chip using
wide traces with multiple vias if using more than one
layer. These connections are to be as short as possible
for loop minimization, with a length to width ratio less
than 20:1 to minimize impedance. DL is the most
critical gate drive, with power ground as its return
path. LX is the noisiest node in the circuit, switching
between VBAT and ground at high frequencies, thus
should be kept as short as practical. DH has LX as its
return path.
BST is also a noisy node and should be kept as short
as possible.
Connect PGND1 pins on the chip directly to the VDDP
decoupling capacitor and then drop vias directly to
theground plane. Locate the current limit resistor at
the chip with a kelvin connection to the phase node.
1.
2.
3.
4.
相關PDF資料
PDF描述
SC4810B High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
SC4810BIMLTRT High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
SC4810BITSTRT High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
SC4810E High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
SC4810EIMLTRT High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
相關代理商/技術參數
參數描述
SC4810B 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
SC4810BIMLTRT 制造商:Semtech Corporation 功能描述:Controller IC Leaded Process Compatible:
SC4810BITSTRT 制造商:Semtech Corporation 功能描述:Controller IC
SC4810E 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:High Performance Current Mode PWM Controller with Complementary Output, Programmable Delay
SC4810EIMLTRT 制造商:Semtech Corporation 功能描述:Controller IC Leaded Process Compatible:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*