- 您現在的位置：買賣IC網 > PDF目錄374731 > SC4808B-2 (Semtech Corporation) High Performance Dual Ended PWM Controller PDF資料下載
參數資料
| 型號： | SC4808B-2 |
| 廠商： | Semtech Corporation |
| 英文描述： | High Performance Dual Ended PWM Controller |
| 中文描述： | 高性能雙端PWM控制器 |
| 文件頁數： | 5/28頁 |
| 文件大小： | 453K |
| 代理商： | SC4808B-2 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
5
2006 Semtech Corp.
www.semtech.com
SC4808B-2
POWER MANAGEMENT
Pin Descriptions
FB:
The inverting input to the PWM comparator. Stray in-
ductances and parasitic capacitance should be minimized
by utilizing ground planes and correct layout guide lines
(see page 19).
REF:
A 0.1μF or 47nF low ESR capacitor is required and
must be placed right at the pin.
CS:
Current sense input and internal slope compensation
are both provided via the CS pin. The current sense input
from a sense resistor is used for the peak current and
overcurrent comparators. An internal 1 to 3 feed back volt-
age divider provides a 3X amplification of the CS signal.
This is used for comparison to the external error amplifier
signal. If an external resistor is connected from CS to the
current sense resistor, the internal current source will pro-
vide a programmable slope compensation. The value of
the resistor will determine the level of compensation. At
higher compensation levels, voltage mode of operation can
be achieved.
RC:
The oscillator programming pin. The oscillator should
be referenced to a stable reference voltage for an accu-
rate and stable frequency. Only two components are re-
quired to program the oscillator, a resistor (tied to Vref and
RC), and a capacitor (tied to the RC and GND). The follow-
ing formula can be used for a close approximation of the
oscillator frequency.
8
×
1
_
TOT
OSC
A
OSC
F
C
R
9
×
1
_
TOT
OSC
B
OSC
F
C
R
where:
Circuit
SC
OSC
TOT
C
C
C
C
+
+
=
4808
pF
C
SC
22
4808
Where the frequency is in Hertz, resistance in ohms, and
capacitance in farads. The recommended range of timing
resistors is between 10 kohm and 200kohm and range of
timing capacitors is between 100pF and 1000pF. Timing
resistors less than 10 kohm should be avoided.
Refer to layout guide lines on (page 19) to achieve best
results.
LUVLO:
Line undervoltage lockout pin. An external resis-
tive divider will program the undervoltage lockout level. The
external divider should be referenced to the quiet analog
ground (see page 19). During the LUVLO, the driver out-
puts are disabled and the softstart is reset. This pin can
also function as an Enable/Disable.
SYNC:
SYNC is a positive edge triggered input with a thresh-
old set to 1.0V. In a single controller operation, SYNC could
be grounded or connected to an external synchronization
clock within the SYNC frequency range (see page 3). In
the Bi-Phase operation mode SYNC pins could be con-
nected to the Cosc (Timing Capacitors) of the other con-
troller. This will force an out of phase operation (see page
12).
GND:
Device power and analog ground. Careful attention
should be paid to the layout of the ground planes (see page
19).
OUTA and OUTB:
Out of phase gate drive stages. The
driver’s peak source and sink current drive capability of
100mA, enables the use of an external MOSFET driver or
a NPN/PNP transistor buffer.
The oscillator RC network programs the oscillator frequency,
which is twice the OUTA/OUTB frequency. To insure that
the outputs do not overlap, a dead time can be generated
between the two outputs by sizing the oscillator timing
capacitor (see page 11).
VCC:
The supply input for the device. Once VCC has ex-
ceeded the UVLO limit, the internal reference, oscillator,
drivers and logic are powered up. A low ESR capacitance,
should be used for decoupling right at the IC pin to mini-
mize noise problems.
相關PDF資料 |
PDF描述 |
|---|---|
| SC4808B-2MSTRT | High Performance Dual Ended PWM Controller |
| SC4808C | High Performance Dual Ended PWM Controller |
| SC4808CMSTRT | High Performance Dual Ended PWM Controller |
| SC4809A | High Performance Current Mode PWM Controller |
| SC4809B | High Performance Current Mode PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC4808B-2_09 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:High Performance Dual Ended PWM Controller |
| SC4808B-2MSTRT | 制造商:Semtech Corporation 功能描述:Current Mode PWM Controller -0.5V to 18V 250mA 10-Pin MSOP T/R 制造商:Semtech 功能描述:Current Mode PWM Controller -0.5V to 18V 250mA 10-Pin MSOP T/R |
| SC4808BIMS.TR | 制造商:Semtech Corporation 功能描述: |
| SC4808BIMSTR | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:High Performance Dual Ended PWM Controller |
| SC4808BIMSTRT | 制造商:Semtech Corporation 功能描述: 制造商:Semtech Corporation 功能描述:SC Series 20 mA 550 kHz SMT High Performance Dual Ended PWM Controller - MSOP-10 |
發布緊急采購，3分鐘左右您將得到回復。